JVC KD-MX2900R Service Manual Download Page 27 | Manualshive

Page: 27 / 86

background image

(1) Cleaning the pick up lens
Before you replace the pick up, please try to
clean the lens with a alcohol soaked cotton
swab.

(2) Life of the laser diode
When the life of the laser diode has expired,
the following symptoms will appear.
(1) The level of RF output (EFM output:ampli
tude of eye pattern) will be low.

Replacement of laser pickup

Replace it.

NO

YES

(3) Semi-fixed resistor on the APC PC board
The semi-fixed resistor on the APC printed
circuit board which is attached to the pickup
is used to adjust the laser power.Since this
adjustment should be performed to match the
characteristics of the whole optical block,
do not touch the semi-fixed resistor.
If the laser power is lower than the specified
value,the laser diode is almost worn out, and
the laser pickup should be replaced.
If the semi-fixed resistor is adjusted while
the pickup is functioning normally,the laser
pickup may be damaged due to excessive current.

Replace the pickup with a normal one.(Refer

to "Pickup Removal" on the previous page)

Test mode is set according to the procedure

described to the adjustment method.

The laser power adjust.

The disc adjust.

End

Dose

recording laser

power (0.68mW) is

output at test

mode?

Replace it.

NO

YES

O.K

Dose

driving current of

the laser diode is

60mA or

less?

Maintenance of laser pickup

«
...
25
26
27
28
29
...
»

Summary of Contents for KD-MX2900R























































































Reviews:

No comments

Related manuals for KD-MX2900R

Brand: Quark-Elec Pages: 2

Brand: Sennheiser Pages: 32

Brand: Magnadyne Pages: 12

Brand: Onkyo Pages: 81

Brand: Teac Pages: 20

Brand: Igloo Pages: 7

Brand: iCartech Pages: 31

Brand: Sennheiser Pages: 1

Brand: B&K Pages: 88

Brand: SXblue GPS Pages: 19

Brand: ECG Pages: 80

Brand: Velleman Pages: 23

Brand: RocketFish Pages: 10

Brand: Yaesu Pages: 23

Brand: Xoro Pages: 40

Brand: Accessmatic Pages: 19

Frankfurt RCM 104

Brand: Blaupunkt Pages: 13

Brand: Blaupunkt Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands