JVC InteriArt HV-32P37SJE Service Manual Download Page 16 | Manualshive

Page: 16 / 44

background image

1-16 (No.YA011)

SECTION 4

ADJUSTMENT

4.1

ADJUSTMENT PREPARATION

(1) There are 2 ways of adjusting this TV : One is with the REMOTE CONTROL UNIT and the other is the conventional method

using adjustment parts and components.

(2) The adjustment using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values which

adjust the screen to the optimum condition can be different from the initial setting values.

(3) Make sure that connection is correctly made AC to AC power source.
(4) Turn on the power of the TV and measuring instruments for warning up for at least 30 minutes before starting adjustments.
(5) If the receive or input signal is not specified, use the most appropriate signal for adjustment.
(6) Never touch the parts (such as variable resistors, transformers and condensers) not shown in the adjustment items of this service

adjustment.

(7) Preparation for adjustment. Unless otherwise specified in the adjustment items, preset the following functions with the REMOTE

CONTROL UNIT.

4.2

MESURING INSTRUMENT AND FIXTURES

(1) DC voltmeter (or digital voltmeter)
(2) HV voltmeter
(3) Oscilloscope
(4) Signal generator (Pattern generator : PAL, SECAM, NTSC)
(5) Remote control unit

4.3

ADJUSTMENT ITEM

B1 POWER SUPPLY check

HIGH VOLTAGE

HORIZONTAL FREQUENCY

FOCUS

IF VCO check

FOCUS ADJUSTMENT

VSM PRESET

VIDEO CIRCUIT

WHITE BALANCE (LOW LIGHT)
WHITE BALANCE (HIGH LIGHT)
SUB BRIGHT
SUB CONTRAST
SUB COLOR
SUB TINT

DEFLECTION CIRCUIT

V SHIFT
V SIZE
H POSITION
H SIZE
SIDE PINC
TRAPEZIUM
CORNER PIN
V LINEARITY

SUB SCREEN

CONTRAST
COLOUR
TINT

Item

Preset value

Item

Preset value

PICTURE MODE

STANDARD

Super Digipure

ON

CONTRAST

Centre

MOVIE THEATER

AUTO

BRIGHT

Centre

BASS / TREBLE / BALANCE

Centre

SHARP

Centre

3D CINEMA SOUND

OFF

COLOUR

Centre

ZOOM

FULL

HUE

Centre

SLEEP TIMER

OFF

COLOUR TEMP

COOL

BLUE BACK

OFF

DIGITAL VNR

AUTO(LOW)

Colour Digipure

AUTO

«
...
14
15
16
17
18
...
»

Summary of Contents for InteriArt HV-32P37SJE













































Reviews:

No comments

Related manuals for InteriArt HV-32P37SJE

Brand: Daewoo Pages: 16

Brand: Daewoo Pages: 54

Brand: Aiwa Pages: 11

20MS334R - 20" Real Flat

Brand: Magnavox Pages: 36

P-Series Quantum X

Brand: Vizio Pages: 48

Brand: Teac Pages: 40

Brand: Xiaomi Pages: 5

Brand: Finlux Pages: 17

Brand: Blaupunkt Pages: 102

Brand: Haier Pages: 11

Brand: Haier Pages: 19

Brand: Haier Pages: 11

Brand: Haier Pages: 10

Brand: Haier Pages: 24

Brand: Haier Pages: 40

Brand: Haier Pages: 10

Brand: Haier Pages: 21

Brand: Haier Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands