JVC HR-XV28SEF Service Manual Download Page 26 | Manualshive

Page: 26 / 131

background image

1-26 (No.YD068)

4.3.6.2

Tape Path Check between Pinch Roller and Take up Guide (Check in the Rev Mode)

1) Check the tape pass status between the pinch roller and the

take-up guide.(Check there is crumpling of the tape pass and
folding of the take-up guide.)

(1) When holding of the take-up guide bottom occurs

Turn the tilt adjusting screw (C) clockwise and travel it sta-
bly to ensure there is no crumbling or folding of the tape.

(2) When holding of the take-up guide top occurs

Turn the tilt adjusting screw (C) anti-clockwise and travel it
stably to ensure there is no crumbling or folding of the tape.

2) Check there is folding of the tape at the bottom or top of the

take-up guide in cutting-off the REV mode

CAUTIONS

If the RF waveform is changed after adjusting the A/C head,
perform fine adjustment to ensure the RF waveform is flat-
ened.

4.3.6.3

Fine Adjustment (Azimuth Adjustment)

4.3.7 X-Value Adjustment

Adjustment Procedure

1) Connect the probe of Oscilloscope to the audio output
jack.
2) Ensure that Audio 1KHz, 7KHz output is flattened at the
maximization point by adjusting the Azimuth adjusting
screw

(A).

Fig. C-5-4

Fixtures and tools used

Connection position

VCR (VCP) status

Adjustment position

Oscilloscope
Standard test tape
(only for SP)
Driver (+) Type 4mm

Audio Output Jack

Play the Alignment tape
1KHz, 7KHz.

Azimuth Adjusting
Screw (A)
Height Adjusting Screw
(B)

1KHz

A: Maximum

7KHz

B: Minimum

Adjustment Procedure

1) After releasing the auto tracking, lightly turn the fixing
  screw. Turn the (+) type driver on the X-dis-tance adju-
  sting hole to the right or left. Adjust the RF envelope
  level to the maximum point and then fix the fixing screws.
2) For the 31 m head, adjust it with the SP tape recorded
  in the width of 31 m since the head travels on the tape
  track only for SP with the width of 58 m.

Fig. C-6

Fixtures and tools used

Connection position

VCR (VCP) status

Adjustment position

Oscilloscope
Standard test tape
(only for SP)
Driver (+) Type 4mm

CH-1: PB RF Envelope
CH-2: NTSC ; SW 30Hz
PAL:SW

25Hz

Head switching output
point
RF Envelope output
point

Play the Alignment tape

Left

X-value Adjusting Hole

Tilt Adjusting Screw (C)

Fixing Screw

Height Adjusting
Screw (B)

Right

Grove of Base A/C

Purpose of adjustment : To maintain compatibility with other VCR (VCP).

RF ENVELOPE OUTPUT POINT

HEAD RF SWITCHING OUTPUT POINT

OSCILLOSCOPE

Connection Diagram

CH-2

CH-1

Azimuth

Adjustment

Screw(A)

«
...
24
25
26
27
28
...
»

Summary of Contents for HR-XV28SEF




































































































































Reviews:

No comments

Related manuals for HR-XV28SEF

Brand: KAMAI Pages: 8

Brand: Cambridge Audio Pages: 2

Brand: Cambridge Audio Pages: 4

Brand: Cambridge Audio Pages: 84

Brand: Cambridge Audio Pages: 8

Brand: Cambridge Audio Pages: 35

Brand: NAD Pages: 30

Brand: NAD Pages: 8

Brand: Classe Audio Pages: 11

Brand: Carver Pages: 31

Brand: E-Bench Pages: 6

Brand: Zenith Pages: 36

Brand: Aiwa Pages: 8

Brand: Coby Pages: 1

Brand: Haier Pages: 15

BDX5500KU Symbio

Brand: Toshiba Pages: 55

Brand: Toshiba Pages: 133

Brand: Pioneer Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands