JVC HR-XV28SEF Service Manual Download Page 7 | Manualshive

Page: 7 / 131

background image

(No.YD068)1-7

2.2

SERVICE INFORMATION FOR EEPROM IC SETTING(VCR)

EEPROM option code No. setting

EEPROM option code No. setting procedure

NAME HEX BINARY

OPT0 00

00000000

OPT1 00

00000000

OPT2 00

00000000

OPT3 00

00000000

OPT4 00

00000000

OPT5 00

00000000

12/26 -

00

V00

-COM Ver.

ID : LG

VERSION : 05 ROM

DATE : 02.17.05

Correction Ver.

MODEL

NAME

HEX

BINARY

HR-XV28SEU OPT0 00

00000000

OPT1

54

00000000

OPT2

60

00000000

OPT3

47

00000000

OPT4

03

00000000

OPT5

0B

00000000

HR-XV28SEK OPT0 00

00000000

OPT1

54

00000000

OPT2

21

00000000

OPT3

87

00000000

OPT4

0D

00000000

OPT5

0B

00000000

HR-XV28SEZ OPT0 00

00000000

OPT1

54

00000000

OPT2

63

00000000

OPT3

47

00000000

OPT4

0D

00000000

OPT5

0B

00000000

HR-XV28SEY OPT0 00

00000000

OPT1

54

00000000

OPT2

63

00000000

OPT3

47

00000000

OPT4

0B

00000000

OPT5

0B

00000000

HR-XV28SER OPT0 09

00000000

OPT1

54

00000000

OPT2

A3

00000000

OPT3

47

00000000

OPT4

0D

00000000

OPT5

0B

00000000

HR-XV28SEF OPT0 00

00000000

OPT1

5C

00000000

OPT2

E8

00000000

OPT3

47

00000000

OPT4

01

00000000

OPT5

0B

00000000

WR : OK I : EXIT MOVE :
EDIT :

1. DETECT NEW EEPROM (OPTION EDIT
SCREEN)
- Eeprom EDIT screen automatically appears if
replacing

Eeprom.

  - Setup option data using the cursor Up/Down key
    of a remote control.
    (Setup upon BOM depending on OPT0~OPT5
  model)
    Since an initial remote control is set to LG for LG
    model, appropriately set optiona data using the
    cursor Up/Down key.

2. EEPROM WRITED AND EEPROM INITIAL
  - Writes data on EEPROM by using REMOCON
    "OK" + FRONT PLAY KEY FOR MORE THAN 5
  SECONDS.

3. PG ADJUST
  1) Payback the SP standard tape
  2) Press the "OK" key on the Remote controller
      and the "PLAY" key on the Front Panel the
      same time, then it goes in to Tracking initial
   mode.
  3) Repeat the above step(No.2), then it finishes
      the PG adjusting automatically.
  4) Stop the playback, then it goes out to PG
      adjusting mode after mony the PG data.

4. BUYER  SELECTION
  - Font ejection key + open/close key for more than
  5

seconds.

  - Option code is displayed in TV
  - First byte of OPTO is changed whenever front
    eject key + open/close key.
  - JVC remote conroller No.0.

«
...
5
6
7
8
9
...
»

Summary of Contents for HR-XV28SEF




































































































































Reviews:

No comments

Related manuals for HR-XV28SEF

Brand: Datavideo Pages: 35

Brand: Samsung Pages: 1

Brand: Samsung Pages: 74

Brand: Aiwa Pages: 15

Brand: Denon Pages: 18

Brand: Linn Pages: 34

Brand: Sampo Pages: 35

Brand: Rotel Pages: 8

Brand: Akai Pages: 8

Brand: Roadstar Pages: 28

Brand: JVC Pages: 20

Freedom ReAct Interactive

Brand: MTI Pages: 30

Brand: Curtis Pages: 22

Brand: Curtis Pages: 24

Brand: JVC Pages: 2

Brand: JVC Pages: 2

Brand: LG Pages: 14

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands