E-74
11. MENU SCREENS
11-9AUDIO Menu Screen
Item
Function
Variation Range
Initial Setting
TEST TONE
AUDIO MODE
A.OUT
AT SEARCH
CH1 FRONT
VR
WIND CUT
AUDIO REF.
LEVEL
AUDIO
SELECT
AUDIO
MONITOR
PAGE BACK
OFF
ON
32K
48K
OFF
ON
DISABLE
ENABLE
OFF
FRONT
REAR
BOTH
–20dB
–12dB
CH1/2
MIX
CH3/4
STEREO
MIX
–––––
OFF
48K
ON
ENABLE
OFF
–20dB
CH1/2
MIX
–––––
Sets whether or not the audio reference signal (1kHz, –20dBFS or
–12dBFS) should be output while the colour bar is output.
OFF: Audio reference signal is not output.
ON: Audio reference signal is output.
Selects the sampling frequency for audio recording (both CH-1 and CH-
2)
32K : Recording is performed with 12-bit, 32 kHz sampling frequency
48K : Recording is performed with 16-bit, 48 kHz sampling frequency
* The DV format offers recording tracks for up to 4 channel when using
12-bit, 32 kHz sampling. The GY-DV5000 records two of these track.
The GY-DV5000 does not allow after-recording.
Selects whether or not audio should be output during search.
OFF : Audio is not output
ON : Audio is output
Used to select whether or not the front section audio level control should
be operative. The front section audio level control only affects the audio
signal recorded on CH1.
DISABLE: Use of the front section audio level control is disabled.
ENABLE: Use of the front section audio level control is enabled.
* The operation of the CH-1 audio level control on the side section is
unaffected by this setting.
To select whether or not the low frequencies of the audio signal from the
audio input connectors are cut. Set to ON to reduce the wind noise of the
microphone.
OFF
: Low frequencies are not cut.
FRONT : Only the low frequencies of the audio signal input to the FRONT
AUDIO IN connector are cut.
REAR : Only the low frequencies of the audio signal input to the REAR
AUDIO IN connector are cut.
BOTH : The low frequencies are cut for both the FRONT and REAR
AUDIO IN connectors.
Sets the reference audio level of the tape (both CH-1 and CH-2).
–20dB : Records with –20 dB as the reference audio level.
–12dB : Records with –12 dB as the reference audio level. Use this setting
when playing back the tape using DV equipment for general
consumer use.
* Use the same setting for playback as for recording.
* This setting is unrelated to the audio level of the DV signal.
(GY-DV5001 only)
Used to select which channels to reproduce when playing back a tape
with sound recorded on 4 channels. (Can only be set in the VTR mode.)
CH1/2 : To reproduce the sound recorded on CH-1 and CH-2.
The GY-DV5000 records audio on the CH-1 and CH-2 channels
during shooting.
MIX
: To simultaneously reproduce the sound of all four channels.
CH3/4 : To reproduce the sound of the CH-3 and CH-4 channels.
Selects whether stereo sound or mixed sound is output from the PHONES
jack when the MONITOR SELECT switch is set to MIX.
STEREO : Stereo sound (CH-1 audio is output from L, CH-2 audio is
output from R)
* Only audio of CH-1 is output from the monitoring loudspeaker.
MIX
: Mixed sound (The mixed CH-1 and CH-2 audio is output
from L and R)
The TOP MENU screen returns when the SHUTTER dial is pressed while
the cursor is at this position.
The GY-DV5000 does not allow after-recording on the CH-3 and CH-
4 channels.
MEMO:
