JVC GR-AXM10 Instructions Manual Download Page 5

Page: 5 / 60

Using the battery pack

Hook-on the battery pack's top end to the
camcorder. (Charging procedure,

pg. 8)

Push in the battery pack until it locks into
place.

To remove the battery pack

Slide BATT. RELEASE and pull out the battery
pack.

QUICK OPERATION GUIDE

Set the power switch to “PLAY”.

Press REW.

— The tape will automatically stop at the

beginning of the tape.

Press PLAY/PAUSE.

— Playback starts and the playback picture

appears in the viewfinder or the LCD
monitor.

• To stop playback, press STOP.

(For more details,

pg. 32.)

• The viewfinder switches off automatically to

save power when the LCD monitor is opened
at an angle of over 45 degrees.

• The LCD monitor turns on/off when it is

opened/closed at approx. 45 degrees.

Or simply play back the tape on a VHS VCR
using the Cassette Adapter (VHS Playpak).

pg. 35

Slide the LENS COVER open/close knob to
open the lens cover.

Set the power switch to “CAMERA”.
— The power indicator will light and an

image will appear in the LCD monitor or
the viewfinder.

Press the Recording Start/Stop button.
— Recording starts.

• To stop recording temporarily, momentarily

press the Recording Start/Stop button once
again.
(For more details,

pg. 15, 16)

• The viewfinder switches off automatically to

save power when the LCD monitor is
opened at an angle of over 45 degrees.

• The LCD monitor turns on/off when it is

opened/closed at approx. 45 degrees.

SUPPLY POWER

INSERTING A VIDEO
CASSETTE

PLAYBACK

SHOOTING

Slide MONITOR OPEN to open the LCD
monitor.
• Open to an angle of over 45 degrees.

Press EJECT to open the cassette holder.

Insert a video cassette.

Press PUSH to close the cassette holder.
(For more details,

pg. 13)

PLAY/PAUSE

STOP

REW

Hook on.

Push in.

BATT. RELEASE

Set to “PLAY”

LENS COVER
open/close knob

Recording Start/Stop button

Set to “CAMERA”

MONITOR OPEN

EJECT

PUSH

Summary of Contents for GR-AXM10





























































Search results

Summary of Contents for GR-AXM10

Reviews:

Related manuals for GR-AXM10

Brands by name

Popular brands

JVC GR-AXM10, Instructions Manual

Search results

Summary of Contents for GR-AXM10

Reviews:

Related manuals for GR-AXM10

Brands by name

Popular brands