JVC GR-AXM10 Instructions Manual Download Page 44

Page: 44 / 60

USER MAINTENANCE

After Use

Set the power switch to POWER OFF to turn off the
camcorder.

Press EJECT to open the cassette holder, then remove
the cassette.

Close and lock the cassette holder by pressing
PUSH.

Close and lock the LCD monitor.

Press BATT. RELEASE to remove the battery pack.

Slide the LENS COVER open/close switch to close
the lens cover.

Cleaning The Camcorder

CLEAN EXTERIOR

Wipe gently with a soft cloth.

CLEAN LCD MONITOR

Slide MONITOR OPEN to open the LCD monitor
and wipe gently with soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.

CLEAN LENS

Blow it with a blower brush, then wipe gently with
lens cleaning paper.

REMOVE EYEPIECE

Turn the eyepiece counterclockwise and pull it out.

CLEAN VIEWFINDER

Remove dust using a blower brush.

RE-ATTACH EYEPIECE

Align the marks, re-attach the eyepiece and turn it
clockwise.

NOTES:

●

Avoid using strong cleaning agents such as benzine or
alcohol.

●

Cleaning should be done only after the battery pack
has been removed or other power units have been
disconnected.

●

Mold may form if the lens is left dirty.

PUSH

EJECT

LENS COVER
open/close switch

Set to “POWER OFF”.

BATT. RELEASE

Remove.

MONITOR OPEN

Marks

Summary of Contents for GR-AXM10





























































Search results

Summary of Contents for GR-AXM10

Reviews:

Related manuals for GR-AXM10

Brands by name

Popular brands

JVC GR-AXM10, Instructions Manual

Search results

Summary of Contents for GR-AXM10

Reviews:

Related manuals for GR-AXM10

Brands by name

Popular brands