JVC GET0199-001A Instructions Manual Download Page 122

Page: 122 / 124

When installing the unit without using the sleeve /

При установке устройства

без использования муфты

In a Toyota for example, first remove the car radio and install the unit in its place.

В автомобилях “Toyota”, например, сначала удалите автомобильную магнитолу, затем установите
на ее место это устройство.

Note

When installing the unit on the mounting bracket, make sure to use the 8 mm-long
screws. If longer screws are used, they could damage the unit.

Примечание :

При установке устройства на крепежный кронштейн, используйте только винты
длиной 8 мм. При использовании более длинных винтов можно повредить
устройство.

When using the optional stay /

При использовании дополнительной

стойки

Install the unit at an angle of less than 30˚.

Установите устройство под углом менее 30°.

PRECAUTIONS on power supply and speaker connections:

•

DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the
unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker

wiring in your car.

Removing the unit

Before removing the unit, release the rear section.

Insert the two handles, then pull them as
illustrated so that the unit can be
removed.

Вставьте два рычажка, затем
потяните их, как показано на рисунке,
чтобы вынуть устройство.

ПРЕДОСТЕРЕЖЕНИЯ по питанию и подключению громкоговорителей:

•

НЕ подключайте провода громкоговорителей к аккумулятору автомобиля, иначе
устройство будет повреждено.

•

ПЕРЕД подключением проводов громкоговорителей к кабелю питания громкоговорителя
проверьте схему соединений громкоговорителей в Вашем автомобиле.

Удаление устройства

Перед удалением устройства освободите заднюю часть.

Screw (option)

Винт (дополнительно)

Stay (option)

Стойка
(дополнительно)

Fire wall

Стена

Dashboard

Приборная панель

Bracket*

Кронштейн

Bracket*

Кронштейн

* Not included with this unit.
*

Не входят в комплект.

Flat type screws (M5 x 8 mm)*

Крепежные винты (M5 x 8 мм)

Pocket

Карман

Flat type screws (M5 x 8 mm)*

Крепежные винты (M5 x 8 мм)

TROUBLESHOOTING

•

The fuse blows.

* Are the red and black leads connected correctly?

•

Power cannot be turned on.

* Is the yellow lead connected?

•

No sound from the speakers.

* Is the speaker output lead short-circuited?

•

Sound is distorted.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

•

Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

•

Unit becomes hot.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

BЫЯВЛЕНИЕ НЕИСПРАВНОСТЕЙ

•

Сработал предохранитель.

Правильно ли подключены черный и красный провода?

•

Питание не включается.

Подключен ли желтый провод?

•

Звук не выводится через громкоговорители.

Нет ли короткого замыкания на кабеле выхода громкоговорителей?

•

Звук искажен.

Заземлен ли провод выхода громкоговорителей?

Заземлены ли разъемы “–” правого (R) и левого (L) громкоговорителей?

•

Шум мешает звучанию.

Соединен ли находящийся сзади зажим заземления с шасси автомобиля с помощью более
короткого и тонкого шнуров?

•

Устройство нагревается.

Заземлен ли провод выхода громкоговорителей?

Заземлены ли разъемы “–” правого (R) и левого (L) громкоговорителей?

Instal1-2_KD-G807_002A_f.p65

1/19/04, 8:01 PM

Summary of Contents for GET0199-001A





























































































































Search results

Summary of Contents for GET0199-001A

Reviews:

Related manuals for GET0199-001A

Brands by name

Popular brands

JVC GET0199-001A, Instructions Manual

Search results

Summary of Contents for GET0199-001A

Reviews:

Related manuals for GET0199-001A

Brands by name

Popular brands