JVC EXAD KD-SHX701 Instructions Manual Download Page 67

Page: 67 / 140

⁄

53 mm

184 mm

KD-SHX701

Installation/Connection Manual
Einbau/Anschlußanleitung
Manuel d’installation/raccordement
Handleiding voor installatie/aansluiting

0404MNMMDWJEIN
EN, GE, FR, NL

LVT1159-006A

[E/EX]

Teileliste für den Einbau und Anschluß

Die folgenden Teile werden zusammen mit
diesem Gerät geliefert.
Nach ihrer Überprüfung, die Teile richtig einsetzen.

Liste des pièces pour l’installation et
raccordement

Les pièces suivantes sont fournies avec cet
appareil.
Après vérification, veuillez les placer correctement.

Lijst van onderdelen die u bij
installatie en aansluiting nodig hebt

De volgende onderdelen worden bij het apparaat
geleverd.
Installeer ze op de juiste wijze, nadat u ze hebt
gecontroleerd.

Parts list for installation and
connection

The following parts are provided for this unit.
After checking them, please set them correctly.

INSTALLATIE (INBOUW IN
HET DASHBOARD)

Op de volgende afbeelding kunt u zien hoe de
installatie, normaal gesproken, in zijn werk gaat.
Neem bij vragen of voor meer bijzonderheden over
inbouwpakketten contact op met uw JVC car audio
dealer of een dealer of een bedrijf dat
inbouwpakketten levert.

•

Als u niet zeker weet hoe u dit apparaat moet
installeren, kunt u dit beter door een daartoe
gekwalificeerde technicus laten doen.

INSTALLATION (MONTAGE
DANS LE TABLEAU DE BORD)

L’illustration suivante est un exemple
d’installation typique. Si vous avez des
questions ou avez besoin d’information sur des
kits d’installation, consulter votre revendeur
d’autoradios JVC ou une compagnie
d’approvisionnement.

•

Si l’on n’est pas sûr de pouvoir installer
correctement cet appareil, le faire installer par
un technicien qualifié.

EINBAU
(IM ARMATURENBRETT)

Die folgende Abbildung zeigt einen typischen
Einbau. Bei irgendwelchen Fragen oder wenn
Sie Informationen hinsichtlich des Einbausatzes
brauchen, wenden Sie sich an ihren JVC
Autoradiohändler oder ein Unternehmen das
diese Einbausätze vertreibt.

•

Sind Sie sich über den richtigen Einbau des
Geräts nicht sicher, lassen Sie es von einem
qualifizierten Techniker einbauen.

INSTALLATION
(IN-DASH MOUNTING)

The following illustration shows a typical
installation. If you have any questions or require
information regarding installation kits, consult
your JVC IN-CAR ENTERTAINMENT dealer or
a company supplying kits.
• If you are not sure how to install this unit

correctly, have it installed by a qualified
technician.

NEDERLANDS

Dit apparaat mag worden gebruikt bij elektrische
systemen die werken op

12 V gelijkstroom met

negatieve aarding

. Als uw auto niet is uitgerust

met een dergelijk systeem, is een spanningsomzetter
vereist. Dit instrument kan worden aangeschaft bij
JVC car audio dealers.

FRANÇAIS

Cet appareil est conçu pour fonctionner sur des
sources de courant continu de

12 V à masse

NEGATIVE

. Si votre véhicule n’offre pas ce type

d’alimentation, il vous faut un convertisseur de
tension, que vous pouvez acheter chez un
revendeur d’autoradios JVC.

DEUTSCH

Dieses Gerät ist für einen Betrieb in

elektrischen Anlagen mit 12 V Gleichstrom
und (–) Erdung ausgelegt

. Verfügt Ihr

Fahrzeug nicht über diese Anlage, ist ein
Spannungsinverter erforderlich, der bei JVC
Autoradiohändler erworben werden kann.

ENGLISH

This unit is designed to operate on 12 V DC,
NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage
inverter is required, which can be purchased at
JVC IN-CAR ENTERTAINMENT dealers.

When you stand the unit, be careful not to damage the fuse on the rear.

Beim Aufstellen des Geräts darauf achten, daß die Sicherung auf der Rückseite nicht beschädigt wird.

Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas endommager le fusible situé sur l’arrière.

Wanneer u het apparaat rechtop zet, moet u erop letten dat u de zekering aan de achterkant niet beschadigt.

Do the required electrical connections.

Nehmen Sie die erforderlichen elektrischen Anschlüsse vor.

Réalisez les connexions électriques.

Breng de vereiste elektrische verbindingen tot stand.

Bend the appropriate tabs to hold the
sleeve firmly in place.

Die geeigneten Zapfen biegen, um
die Manschette sicher festzuhalten.

Tordez les languettes appropriées
pour maintenir le manchon en place.

Buig de vereiste lipjes zodat de huls goed
op zijn plaats wordt gehouden.

Removing the unit

Before removing the unit, release the rear
section.

Ausbau des Geräts

Vor dem Ausbau des Geräts den hinteren Teil
freigeben.

Retrait de l’appareil

Avant de retirer l’appareil, libérer la section
arrière.

Verwijderen van het apparaat

Voordat u het apparaat verwijdert, moet u het
achtergedeelte losmaken.

Insert the two handles, then pull them as
illustrated so that the unit can be removed.

Die beiden Handgriffe einsetzen und dann
ziehen wie in der Abbildung gezeigt, so daß
das Gerät entfernt werden kann.

Insérez les deux poignées, puis tirez de la
façon illustrée de façon à retirer l’appareil.

Plaats de twee hendels en trek ze vervolgens zoals
afgebeeld naar voren zodat het toestel kan worden
verwijderd.

Handles

Griffe

Poignées

Hendels

Washer (ø5)

Unterlegscheibe (ø5)

Rondelle (ø5)

Sluitring (ø5)

Lock nut (M5)

Sicherungsmutter (M5)

Ecrou d’arrêt (M5)

Contra-moer (M5)

Mounting bolt (M5 x 20 mm)

Befestigungsschraube (M5 x 20 mm)

Boulon de montage (M5 x 20 mm)

Bevestigingsbout (M5 x 20 mm)

Rubber cushion

Gummipuffer

Amortisseur en caoutchouc

Rubberdop

Hard case/Control panel

Etui/Schalttafel

Etui de transport/Panneau
de commande

Behuizing/Bedieningspaneel

Sleeve

Halterung

Manchon

Huis

Trim plate

Frontrahmen

Plaque d’assemblage

Sierplaat

Power cord

Stromkable

Cordon d’alimentation

Stroomkabel

Battery

Batterie

Pile

Batterij

Remote controller

Fernbedienung

Télécommande

Afstandsbediening

CD-ROM (Image Converter Color)

CR2025

Fit the protrusions outside the unit.

Die Vorsprünge außen am Gerät anpassen.

Fixez les protubérances à l’extérieur de l’appareil.

Plaats de uitsteeksels buiten het toestel.

RM-RK300

Instal1-2_KD-SHX701_006A_f.p65

4/1/04, 3:11 PM

Summary of Contents for EXAD KD-SHX701













































































































































Search results

Summary of Contents for EXAD KD-SHX701

Reviews:

Related manuals for EXAD KD-SHX701

Brands by name

Popular brands

JVC EXAD KD-SHX701, Instructions Manual

Search results

Summary of Contents for EXAD KD-SHX701

Reviews:

Related manuals for EXAD KD-SHX701

Brands by name

Popular brands