JVC DT-3D24G1 Instructions Manual Download Page 32

Page: 32 / 36

Specifications

General

Model name

DT-3D24G1

Type

MULTI FORMAT 3D LCD MONITOR

Screen size

Type 24 wide format

Aspect ratio

16:10

Compliant video signal format

→

“Available signals” on page 33

Format

3G SDI
DUAL LINK HD SDI
HD SDI
SD SDI

EMBEDDED AUDIO

:
:
:
:

SMPTE424M/SMPTE425M
SMPTE372M
BTA S-004C, SMPTE292M
ITU-R BT.656:

525/625

SMPTE259M: 525
SMPTE299M, SMPTE272M

Audio output

Internal speaker: 1.0 W + 1.0 W

Operation environment

Operating temperature: 5°C – 35°C (41°F – 95°F)
Operating humidity: 20% – 80% (non-condensing)
(Slightly variable depending on ambient conditions for installation.)

Power requirements

AC 120 V/AC 220 – 240 V, 50 Hz/60 Hz, or DC 24 V (Voltage range: DC 23.3 V − DC 25.5 V)

Rated current

1.15 A (AC 120 V)
0.67 A (AC 220 – 240 V)
4.8 A (DC 24V)

External dimensions (excluding
protruding parts)

Width:

564 mm (22 1/4˝)

Height: 448.6 mm (17 3/4˝)

408 mm (16 1/8˝)

Depth: 243 mm (9 5/8˝)

99 mm (4˝)

(with the stand)

(without the stand)

Mass

12.0 k

(26.4 lbs) (with the stand) 9.1 k

(20.0 lbs) (without the stand)

Accessories

AC power cord, Power cord holder × 1, Screw × 2 (for power cord holder),
Circular polarizing glasses × 2 (for 3D viewing, not under warranty)

LCD panel

Type

24˝ wide, active matrix TFT

Effective screen size

Width: 518.4 mm (20 1/2˝) Height: 324 mm (12 7/8˝) Diagonal: 611.3 mm (24 1/4˝)

Number of pixels displayed

1920 × 1200

Number of colors displayed

16.77 million

Contrast ratio (TYP.)

1000:1

Input/output terminals

Video

DVI-D (HDCP)

DVI-D signal input (compatible with HDCP): DVI-D connector x 1 (compatible with DDC2B)

E. AUDIO 3G SDI/HD SDI/SD SDI (IN 1/L)

Digital signal input (compatible with EMBEDDED AUDIO/DUAL LINK signals):
Auto detection, 2 line, BNC connector x 2

E. AUDIO 3G SDI/HD SDI/SD SDI (IN 2/R)

E. AUDIO 3G SDI/HD SDI/SD SDI
(ACTIVE OUT)

Digital signal output (compatible with EMBEDDED AUDIO signals):
2 line reclocked out, BNC connector x 2

Audio

AUDIO (IN)

Analog audio signal input: 1 line, RCA connector x 2,
500 mV (rms), high impedance

AUDIO (MONITOR OUT)

Analog audio signal input: 1 line, RCA connector x 2,
500 mV (rms)

External control

REMOTE (MAKE/TRIGGER)

→

“Using the MAKE/TRIGGER system” on page 26

REMOTE (RS-485)

→

“Using the serial communication” on page 28

REMOTE (RS-232C)

DT3D24G1̲EN.indb 32

11.1.25 0:53:57 PM

Summary of Contents for DT-3D24G1





































Search results

Summary of Contents for DT-3D24G1

Reviews:

Related manuals for DT-3D24G1

Brands by name

Popular brands

JVC DT-3D24G1, Instructions Manual

Search results

Summary of Contents for DT-3D24G1

Reviews:

Related manuals for DT-3D24G1

Brands by name

Popular brands