JVC CA-MXDVA9 Service Manual Download Page 8 | Manualshive

Page: 8 / 73

background image

MX-DVA9/MX-DVA9R

1-8

Prior to performing the following procedure, remove
the metal cover.

Disconnect the card wire from connector CN542 on
the main board on the right side of the body.

Disconnect the wire from CN501 on the DVD servo
board in the lower part of the DVD mechanism
assembly, on the left side of the body.

Remove the screw F from the rear panel on the
back of the body. Disconnect the earth terminal
extending from the DVD changer mechanism
assembly and attached to the terminal on the
antenna board.

Remove the two screws C on top of the body and
the two screws D on back of the body.

Remove the DVD changer mechanism from behind
upward while pulling the front panel assembly and
the rear panel outward.

1.

2.

3.

Disconnect the card wire from connector CN540 and
CN541 on the inner side of the main board on the
right side of the body, and remove the DVD
mechanism assembly.

6.

Removing the DVD mechanism assembly
(See Fig.4 to 7)

At this point, the two card wires in the
lower part of the DVD mechanism
assembly is still connected.

REFERENCE:

To prevent damage to the DVD fitting, be
sure to pull both the rear panel and the
front panel assembly enough to remove
the DVD changer mechanism assembly.

REFERENCE:

To prevent damage to the DVD changer
mechanism assembly, make sure to pull
both the front panel assembly and the rear
panel outward enough to remove the DVD
changer mechanism assembly.

REFERENCE:

Fig.4

Fig.5

Fig.6

Fig.7

Front panel assembly

C

C

DVD changer
mechanism assembly

Rear panel

Main board

CN542

DVD changer mechanism assembly

D

Tuner board

Front panel assembly

Rear panel

Front panel assembly

DVD changer mechanism assembly

CN501

Rear panel

Main board

CN542

CN541

CN540

F

DVD changer mechanism assembly

Rear panel

Earth terminal

Tuner board

«
...
6
7
8
9
10
...
»

Summary of Contents for CA-MXDVA9










































































Reviews:

No comments

Related manuals for CA-MXDVA9

Brand: JBL Pages: 8

Brand: Samson Pages: 52

Brand: York Pages: 6

Brand: EAW Pages: 91

Brand: KEF Pages: 4

Brand: KEF Pages: 12

Brand: Ace Pages: 13

Brand: ICP DAS USA Pages: 28

Brand: iDance Pages: 13

Brand: M-E Pages: 20

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 12

Brand: Pan Acoustics Pages: 18

Brand: Safeline Pages: 76

Brand: Sanlien Pages: 42

Brand: JBL Pages: 8

Brand: JA Audio Pages: 4

Brand: Fenton Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands