JVC CA-MXDVA9 Service Manual Download Page 15

Page: 15 / 73

MX-DVA9/MX-DVA9R

1-15

<Front panel assembly>

Prior to performing the following procedure, remove
the metal cover, the DVD changer mechanism
assembly and the front panel assembly.

Disconnect the card wire from connector CN306 on
the head amplifier & mechanism control board.

Remove the seven screws N attaching the cassette
mechanism assembly.

Removing the cassette mechanism
assembly (See Fig.31)

Remove the four screws O attaching the stay
bracket.

Disconnect the card wires from connector CN316
and CN881 on the display system control board.

Remove the six screws P attaching the display
system control board.

If necessary, disconnect the wire from connector
CN870 on the front side of the display system control
board and unsolder FW915.

Removing the display system control
board (See Fig.32 to 34)

Fig.31

Head amplifier
& mechanism control board
CN306

Cassette mechanism
assembly

Fig.32

Fig.33

Fig.34

Display system control board

Stay bracket

CN881

FW915

(Solding)

Display system control board

FW915

CD eject board

CN911

Display system control board

CN870

CN316

Summary of Contents for CA-MXDVA9










































































Search results

Summary of Contents for CA-MXDVA9

Reviews:

Related manuals for CA-MXDVA9

Brands by name

Popular brands

JVC CA-MXDVA9, Service Manual

Search results

Summary of Contents for CA-MXDVA9

Reviews:

Related manuals for CA-MXDVA9

Brands by name

Popular brands