JVC CA-MXDVA9 Service Manual Download Page 29

Page: 29 / 73

MX-DVA9/MX-DVA9R

1-29

DVD section

Are Code FL indicate of Area Code in Test mode

a) Insert A/C Power Cord

b) At standby mode press Stop Button and CANCEL/DEMO button.

Wait 4 seconds & for the display of " TEST VERSION REGION " i.e. TEST JC 1

c) Press the 'ENTER' button on remocon. The FL panel will display 'EEPROM'.

Plug out and plug in again the power cord. Repeat the process 1(a) and 1(b) again.

Confirm that the Area Code and Region Code is correctly display as below.

Region Code.

Note: Please plug out and plug in the power cord from A/C supply before continue the next test.

J/C

UG/UX

US/UN/UP

E/EN/B

TEST MODE FOR DVD a INITIALISE THE DVD UNIT BOARD

Adjustment
Jig setup

1. Remove the rubber cushion from each of the four

corners of the traverse mechanism.
(When installing be sure not to make a mistake with
the cushion colors).

2. Install the jig stud.
3. Make a jig clamp. (Remove the clamp from the set

and assemble it as shown in the diagram below.

Note:

How to handle the pickup
To protect the pickup from electro-static damage,
make sure to hold it by the die-cast chassis (optical
base). And make sure that pickup lens do not touch
the top cover.

Green rubber
cushion

Blue rubber
cushion

Jig stud

Installing the
4 jig studs

How to prepare a clamp

Remove the claws
from the 3 locations

Disassemble the clamp
and holder

Combine the clamp
and holder to become
a jig clamp.

Summary of Contents for CA-MXDVA9










































































Search results

Summary of Contents for CA-MXDVA9

Reviews:

Related manuals for CA-MXDVA9

Brands by name

Popular brands

JVC CA-MXDVA9, Service Manual

Search results

Summary of Contents for CA-MXDVA9

Reviews:

Related manuals for CA-MXDVA9

Brands by name

Popular brands