Juta CM3024Z Installation And Operation Manual Download Page 6

JUTA Solar Charge Controller

Model :CM3024Z

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Ningbo Star Solar Co.,Ltd Tel:(86) 574 26266608

Fax:(86) 574 26266618 56664636 Email:[email protected]

Http://www.pvsolarchina.com

controller will reconnect the load loop automatically. 
At this interface, press button  (

5 seconds),the number starts to flicker, and it means 

the controller enters into the interface of setting the recovery voltage. Use button 

 

to adjust this parameter. After finishing setting, press button  (

5 seconds) to exit 

 

.10 Review and setting the voltage of ceasing charging 

voltage of ceasing charging. 

this interface and the controller can store this setting number

3

As shown as the right figure, the displaying number is the 
When the battery voltage reaches up to this voltage, the controller will disconnect the 
charging loop to prevent the battery from overcharging. After the battery voltage drops, 
the controller will reconnect the charging loop. At this interface, press button   for 
long(

5 seconds),the number starts to flicker, and it means the controller enters into the 

interface of setting the voltage of ceasing charging. Use button 

 to adjust this 

parameter. After finishing setting, press button   for long(

5 seconds) to exit this 

interface and the controller can store this setting number.

 

 

3.11 Review and setting the load mode 

the reviewing surface  of  the  load

the  condition  of                 

1h~23h— indicating delayed mode of light control, loads start to supply power after 

Oh— indi

p working 

At this interface, press button 

As shown as the right figure, it is 

                                     

mode. Different numbers represent different load mode.

 

24h—indicating  normal  mode,  loads  are  under 

supplying power without breakdown; 

dark and shun down after working for the delayed setting hours   

cating light control, loads start to supply power after dark and sto

after dawn. 

 for long(

5 seconds),the number starts to flicker, 

tton 

and it means the controller enters into the interface of setting the load modes. Use bu

  to adjust this parameter. After finishing setting, press button   for long(

 

5 s

4.B eakdown & disposal 

figure, it means the battery voltage is lower 

the pr

 voltage. The controller enters into the low voltage protection st

 

 battery 

ad, 

verloading protection & disposal: 

 figure, and the light flickers, it mean the 

curr

 

econds) to exit this interface and the controller can store this setting number. 

 
 
 

 

r

Low voltage protection & disposal: 

If the screen shows as the right 

than  

otection

ate and the load

loop disconnects. Use the solar panels or charger to charge for the battery. When
voltage recovers to the protection voltage, the controller will recover to supply power for lo
and enter into the working state. 

 
O

If the screen shows as the right

ent of the load loop is 1.2 times of the rated current within 3 seconds, and

the controller is at overloading state. After removing some loads, the controller
power to the loads automatically within seconds, or you can press button

 will supply 

  to recover the

power supply compulsively. 
 

 

hort-circuit protection & disposal: 

 figure, and the light flickers, it means 

ther

S

If the screen shows as the right

e happens short-circuit in the load loop, and the controller is at 

6

Summary of Contents for CM3024Z








Reviews: