Juta CM3024Z Installation And Operation Manual Download Page 5

JUTA Solar Charge Controller

Model :CM3024Z

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Ningbo Star Solar Co.,Ltd Tel:(86) 574 26266608

Fax:(86) 574 26266618 56664636 Email:[email protected]

Http://www.pvsolarchina.com

This interface is the main interface, and it shows the charging &    discharging state, 

battery capacity and battery voltage. 
 
   

 3.2

 Load ON/OFF controlling

 

At the battery voltage review interface, you can press button 

  to turn on or turn off the 

load, while this button does not have this function at other interfaces. 
 

     

  3.3 Environmental temperature review

 

Be used for the temperature compensation when the battery ceases charging. 

As shown as the right figure, the displaying number is the surrounding 
environmental temperature of the controller,   

3.4 Review the generating current of solar panels 

           

As shown as the right figure, the displaying number is the generating   

current of solar panels. 

 

3.5 The load current review 

           

As shown as the right figure, the displaying number is the load   

current. 

 

3.6 Review and clearing the accumulative generating AH of solar 

panels 
         

As shown as the right figure, the displaying number is the accumulating 

ting AH of sola

genera

r panels 

At this interface, press button  (

5 seconds), and it can clear 

       

3.7 Review and clearing load accumulative discharging AH 

     

umulative 

tton 

accumulative generating AH. 

   

 

 

   

As shown as the right figure, the displaying number is the acc

discharging AH of loads. 
At this interface, press bu

(

5 seconds), and it can clear 

       

 and setting low voltage protection function 

rotection 

 

ess button 

accumulative discharging AH. 
 

3.8 Review

As shown as the right figure, the displaying number is the p
voltage. And if the battery voltage is lower than this voltage, the 
controller will disconnect the load loop to prevent the battery from
over-discharging. 
At this interface, pr

 for long(

5 seconds),the number starts to flicker, 

and it means the controller enters into the interface of setting the protection voltage. 
Use button 

  to adjust this parameter. 

After finishing setting, press button   for long(

5 seconds) to exit this interface and the 

3.9 Review and setting recovering voltage for low voltage condition 

As shown as the right figure, the displaying number is the recovery

 

      

controller can store this setting number. 

 

 

 

 

number. After the controller enters into low voltage protection state,  

         

and when the battery voltage recovers to be higher than the recovering voltage, then th

5

Summary of Contents for CM3024Z








Reviews: