Juta CM3024Z Installation And Operation Manual Download Page 4

JUTA Solar Charge Controller

Model :CM3024Z

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Ningbo Star Solar Co.,Ltd Tel:(86) 574 26266608

Fax:(86) 574 26266618 56664636 Email:[email protected]

Http://www.pvsolarchina.com

3. Operation 

1. Explanation of LCD Graphic Symbol 

     

     

   

     

 
 
 
 
 
 
 
 
 
 
 

                                   
2 . Explanation of button function: 
         

:

Interfaces circular toggling button. Use this button can realize the toggling circularly 

among the interfaces. The circular order is as follows: as shown as figure 1 

:

 Parameter adjusting

‘+’

+ button. Besides, under parameter review condition, press this 

button for over 5 seconds, and all the parameters will recover to the ex-work setting 
state. 

 

:

Parameter adjusting‘–’button. Besides, at the main interface, this button can turn on 

or turn off the load. 

 

                                                                                 

 
3. Parameter review and setting: 

After the controller electrifies right, it will enter into 
the displaying interface of battery voltage. This 
interface is the main interface of the controller. Press 
button 

 to go through the interfaces of the 

following parameters. If the interface can be reset, 
press button   for  long(

5 seconds, and the 

number on the interface starts to flicker), then it 
enters into the setting interface of this parameter. 
After finishing setting, press button   

f

r long to exit 

the setting interface, and the number stops 
flickering

o

 

3.1 Battery voltage review 

         

As shown as the right figure, the displaying 

number is the present     

battery voltage. 

Summary of Contents for CM3024Z








Reviews: