9
In die Befestigungs- und Scharnierlöcher
beiliegende Abdeckkappen (B) eindrücken.
D727
C
D
D726
B
Tür öffnen und Gerät gegenüber der Bandseite an
die Möbelseitenwand anrücken. Gerät mit den 4 bei-
liegenden Schrauben befestigen.
Belüttungsgitter (C) und Scharnierabdeckung (D)
aufstecken.
Gerät in die Nische einschieben bis die
Anschlagleiste (A) unten am Möbel anliegt.
A
D022
PR266
A
B
C
D
Die Teile A, B, C, D abnehmen, wie in der Abb.
gezeigt wird.
Fugenabdeckprofil oben um die Winkeldicke
ausschneiden und zwischen Gerät und
Möbelseitenwand eindrücken.
D724
12
CONTENTS
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Use - Cleaning the interior - Control Panel - Operation - Temperature regulation - Quick-freezing . . . . . . . . . . . .
Warning light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Use - Freezing fresh food - Storage of frozen food - - Thawing - Ice-cube production - Hints - Hints for freezing .14
Hints - Hints for storage of frozen food - Maintenance - Periods of no operation - Periodic cleaning . . . . .
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Customer service and spare parts - Installation - Location - Electrical connection - Door reversibility . .
Building-in instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
•
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance.
Installation
• During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. For safety reasons, minimum
ventilation must be as shown in the relevant
Figure.
Attention: keep ventilation openings clear of
obstruction.
• If the appliance is transported horizontally, it is
possible that the oil contained in the compressor
flows in the refrigerant circuit. It is advisable to
wait at least two hours before connecting the
appliance to allow the oil to flow back in the
compressor.
• There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
• Parts which heat up should not be exposed.
Wherever possible the back of the product
should be against a wall.
• If the appliance has been transported
horizontally, it is possible that the oil contained in
the compressor ílows in the refrigerant circuit. It
is advisable to wait at least two hours before
connecting the appliance to allow tlıe oil to flow
back in the compressor.
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol
are recyclable.
