Jungheinrich HC 10, Operating Instructions Manual

Page: 28 / 37

F 1
0708
.GB
F Maintenance of the fork-lift truck
1 Operational safety and environmental protection
The checks and servicing operations contained in this chapter must be performed in
accordance with the intervals as indicated in the servicing checklists.
f
Modifications of fork-lift truck assemblies, especially of the safety installations, are not
permitted. On no account must the operational speeds of the truck be changed.
m
Only original spare parts have been certified by our quality assurance service. To en-
sure safe and reliable operation of the fork-lift truck, only spare parts of the manufac-
turer must be used. Used parts, oils and fuels must be disposed of in accordance with
the applicable environmental protection regulations. For oil changes, the oil service
of the manufacturer is available to you.
Upon completion of any checking and servicing activities, the operations contained in
the section “Recommissioning” must be performed (see section F).
2 Safety regulations applicable to truck maintenance
Servicing and maintenance personnel: The fork-lift truck must only be serviced
and maintained by trained personnel of the manufacturer. The service organization
of the manufacturer has external technicians trained especially for these assign-
ments. We thus recommend signing a maintenance contract with the relevant service
location of the manufacturer.
Lifting and jacking up: When a fork-lift truck is to be lifted, the lifting gear must only
be secured to the points specially provided for this purpose. When the truck is to be
jacked up, suitable measures must be taken to prevent the truck from slipping or tip-
ping over (use of wedges, wooden blocks). Work underneath the raised load lifting
device must only be carried out when the fork is immobilised and supported by a
chain of adequate strength.
Cleaning operations: No inflammable liquids must be used when cleaning the fork-
lift truck. Prior to commencing cleaning operations, all safety measures that are re-
quired to prevent sparking (e.g. by short-circuits) have to be taken. In the case of bat-
tery driven vehicles, remove the battery cable or ensure that the batteries are discon-
nected. Only weak indraft, weak compressed air and non-conducting, antistatic
brushes must be used for the cleaning of electric or electronic assemblies.
m
If the fork-lift truck is to be cleaned using a water jet or a high-pressure cleaner, all
electric and electronic components must be carefully covered beforehand because
moisture can lead to incorrect functioning.
Cleaning by means of a steam jet is not permitted.
Upon completion of cleaning work, the operations detailed in the section “Recommis-
sioning” must be performed.
F 1
0708
.GB
F Maintenance of the fork-lift truck
1 Operational safety and environmental protection
The checks and servicing operations contained in this chapter must be performed in
accordance with the intervals as indicated in the servicing checklists.
f
Modifications of fork-lift truck assemblies, especially of the safety installations, are not
permitted. On no account must the operational speeds of the truck be changed.
m
Only original spare parts have been certified by our quality assurance service. To en-
sure safe and reliable operation of the fork-lift truck, only spare parts of the manufac-
turer must be used. Used parts, oils and fuels must be disposed of in accordance with
the applicable environmental protection regulations. For oil changes, the oil service
of the manufacturer is available to you.
Upon completion of any checking and servicing activities, the operations contained in
the section “Recommissioning” must be performed (see section F).
2 Safety regulations applicable to truck maintenance
Servicing and maintenance personnel: The fork-lift truck must only be serviced
and maintained by trained personnel of the manufacturer. The service organization
of the manufacturer has external technicians trained especially for these assign-
ments. We thus recommend signing a maintenance contract with the relevant service
location of the manufacturer.
Lifting and jacking up: When a fork-lift truck is to be lifted, the lifting gear must only
be secured to the points specially provided for this purpose. When the truck is to be
jacked up, suitable measures must be taken to prevent the truck from slipping or tip-
ping over (use of wedges, wooden blocks). Work underneath the raised load lifting
device must only be carried out when the fork is immobilised and supported by a
chain of adequate strength.
Cleaning operations: No inflammable liquids must be used when cleaning the fork-
lift truck. Prior to commencing cleaning operations, all safety measures that are re-
quired to prevent sparking (e.g. by short-circuits) have to be taken. In the case of bat-
tery driven vehicles, remove the battery cable or ensure that the batteries are discon-
nected. Only weak indraft, weak compressed air and non-conducting, antistatic
brushes must be used for the cleaning of electric or electronic assemblies.
m
If the fork-lift truck is to be cleaned using a water jet or a high-pressure cleaner, all
electric and electronic components must be carefully covered beforehand because
moisture can lead to incorrect functioning.
Cleaning by means of a steam jet is not permitted.
Upon completion of cleaning work, the operations detailed in the section “Recommis-
sioning” must be performed.