junger X*AP RM1 Manual Download Page 15

 

 

D*AP4 VAP

 

    86 

 

Safety Information 

 
Electrical 

 

Safety classification: 

Class 1 – grounded product / Schutzklasse 1 

 

Corresponding to EN 60065:2002 

 

Power connection: 

The device must be connected to a power socket that provides a 
protective earthing conductor. 

 

Power switch: 

The power switch is a toggle switch placed at the rear of the device. 

 

The ON / OFF position is indicated by engravings [I] / [o] on the lever. It must be 
reached without difficulty. 
The devices may be equipped with dual power supply, in this case it will have 
two power cords and switches. You must inform yourself about the location and 
assignment of the switches. 

 

Water protection: 

The device must not be exposed to splash or dripping water. 

 

It is permitted to place a container filled with liquids (e.g. vases) 

 

on top of the device. 

 
Service safety 

Only qualified personnel should perform service procedures. 

 

Do not service alone: 

Do not perform internal service or adjustments of the device unless another 
person capable of rendering first aid and resuscitation is present. 

 

Disconnect power: 

To avoid electrical shock, switch off the device power, then disconnect the 
power cord from the mains power. Do not block the power cord; it must remain 
accessible to the user at all times 

 
To avoid fire or personal injury 
 

Mounting: 

It must be placed on a flat surface or must be mounted  into an 19" rack.  
It is recommended to use metal brackets (sheet steel angle) to support the 
device. 

 

Provide proper 

this case and if the device has a built in fan, a gap of at least 1cm must be 

Ventilation  

left between the device edge and the steel angle. It is highly recommended to 
leave a gap of at least 1RU above and below the device. 

 

Use proper power cord  Use only the power cord specified for this product and certified for the country of 

use. 

 

Do not operate 

Do not operate this product with covers or panels removed. 

without covers 

 

Do not operate 

If you suspect that there is damage to this product, have it inspected  

with suspected failures 

by qualified service personnel. 

 

Risk of explosion: 

The device contains a lithium battery. If replaced incorrectly or by a different or 
inadequate type an explosion may occur. 

 
 

Warranty 

 
Standard Junger Audio one-year warranty on parts and labor. 
 
 
 

Specifications are subject to change without notice 

 

Summary of Contents for X*AP RM1

















Reviews: