background image

Connection mode KNX 

Connection terminal 

Ambient temperature 

-5 ... +45 °C 

Storage/transport temperature 

-25 ... +70 °C 

Safety class 

III 

5.2 Accessories 

Cover 1-gang 

Art.-No.: FD..901 TSA.. 

Cover 2-gang 

Art.-No.: FD..902 TSA.. 

Cover 4-gang 

Art.-No.: FD..904 TSA.. 

Cover with symbol, 1-gang 

Art.-No.: FD ..901 TSAP.. 

Cover with symbol, 2-gang 

Art.-No.: FD ..902 TSAP.. 

Cover with symbol, 4-gang 

Art.-No.: FD ..904 TSAP.. 

Cover with inscription field, 1-gang 

Art.-No.: FD ..901 TSANA.. 

Cover with inscription field, 2-gang 

Art.-No.: FD ..902 TSANA.. 

Cover with inscription field, 4-gang 

Art.-No.: FD ..904 TSANA.. 

5.3 Warranty 

We reserve the right to make technical and formal changes to the product in the interest of 
technical progress. 
We provide a warranty as provided for by law. 
Please send the unit postage-free with a description of the defect to our central customer 
service office: 

ALBRECHT JUNG GMBH & CO. KG 

Service Center 
Kupferstr. 17-19 
D-44532 Lünen 
Service-Line: +49 (0) 23 55 . 80 65 51 
Telefax: +49 (0) 23 55 . 80 61 89 
[email protected] 

General equipment 

Service-Line: +49 (0) 23 55 . 80 65 55 
Telefax: +49 (0) 23 55 . 80 62 55 
[email protected] 

KNX equipment 

Service-Line: +49 (0) 23 55 . 80 65 56 
Telefax: +49 (0) 23 55 . 80 62 55 
[email protected] 

The 

Œ

 symbol is a free trade symbol, which is solely intended for the authorities and does not 

guarantee any properties. 

ALBRECHT JUNG GMBH & CO. KG 

Volmestraße 1 
D-58579 Schalksmühle 

Telefon: +49.23 55.8 06-0 
Telefax: +49.23 55.8 06-1 89 
E-mail: [email protected] 
Internet: www.jung.de 
              www.jung-katalog.de 

7/7 

32558813 
J:0082558813 

19.06.2009 

Push-button module with integrated BCU Standard / Universal 

Summary of Contents for 3091 TSM








Reviews: