manualshive.com logo in svg

JUMO Quantrol LC100, Operating Manual, Page: 5 / 40

Share
Download
JUMO Quantrol LC100 Operating Manual Download Page 5

5

1 Introduction

1.1

Device documentation

Data sheet T 702030 (as a PDF document)

The data sheet contains general information about the device and forms the basis for planning 
and purchase decision.

Brief instructions B 702030.7 (printed in DIN A6 format)

These brief instructions contain the most important information about installation, the electrical 
connection as well as operation, parameterization and configuration of the device. The brief ins-
tructions are supplied with every device. For further information, please refer to the operating ma-
nual B 702030.0 available as a PDF document.

Operating manual B 702030.0 (as a PDF document)

This operating manual contains all information about installation, the electrical connection as well 
as operation, parameterization and configuration of the device.

Interface description B 702030.2.0 (as a PDF document)

It contains information about the RS485 interface, the Modbus protocol and the communication 
with other devices. 

All 

PDF documents

 can be downloaded under 

www.jumo.net

.

1.2

Safety information

This manual contains information that must be observed in the interest of your own safety and to 
avoid damage to assets. This information is supported by symbols which are used in this manual 
as follows.
Please read this manual before starting up the device. Keep the manual in a place accessible to 
all users at all times.
All necessary settings are described in this manual. Manipulations not described in this manual 
or expressly forbidden will jeopardize your warranty rights.

Warning signs

DANGER!

This symbol indicates that 

Injury or death caused by electrical shock 

can occur, if the 

respective protective measures have not been taken.

CAUTION!

This symbol in combination with the signal word indicates that 

damage to assets or data 

loss

 will occur if suitable precautions are not taken.

READ DOCUMENTATION!

This symbol – placed on the device – indicates that the associated 

device docu-

mentation has to be observed

. This is necessary to recognize the kind of the 

potential hazards as well as to take the measures to avoid them.

Summary of Contents for Quantrol LC100









































Reviews:

No comments