manualshive.com logo in svg

JUMO Quantrol LC100, Operating Manual, Page: 17 / 40

Share
Download
JUMO Quantrol LC100 Operating Manual Download Page 17

17

3 Operation - Configuration - Parameterization

3.2.3

Ramp function/firing curve (rAFC)

The device can be operated as a fixed value controller with and without ramp function. In addi-
tion, a firing curve is supported.

ConF

 -> 

rAFC

 ->

3.2.4

Limit value monitoring (Li1, Li2)

The device is equipped with two functions for limit value monitoring (Li 1, Li 2) each with eight 
different alarm functions (AF1 to AF8). The two output signals are available for binary functions.

ConF

 -> 

LiI

 , 

Li2

 ->

Parameters

Value

Description

Function

FnCt

0

Ramp function/firing curve switched off

1

Ramp function Kelvin/Minute

2

Ramp function Kelvin/Hour

3

Ramp function Kelvin/Day

4

Firing curve Kelvin/Minute

5

Firing curve Kelvin/Hour

6

Firing curve Kelvin/Day

Ramp rate

rASL

0

 ...

999

Value of the ramp rate (only for function = 1 to 6)

(Setup program: For the firing curve, timer value, time unit and setpoint can also be set here.)

Parameters

Value

Description

Alarm function

FnCt

0

Limit value monitoring switched off

1

AF1: Limit value above and below the setpoint (monitoring 
range); symmetric or asymmetric

2

AF2: As AF1, output signal inverted

3

AF3: Limit value below the setpoint 

4

AF4: As AF3, output signal inverted

5

AF5: Limit value above the setpoint 

6

AF6: As AF5, output signal inverted

7

AF7: Fixed limit value (setpoint independent)

8

AF8: As AF7, output signal inverted

Limit value

AL

, 

AL2

-1999 ... 

0

 ...

+9999

Limit value to be monitored

For asymmetrical limit value: AL is below the setpoint, AL2 is 
above the setpoint.

Limit value range for AF1 and AF2: 0 to  9999

Switching

differential

HySt

0 ... 

1

 ...

9999

Switching differential in respect to the limit value

Summary of Contents for Quantrol LC100









































Reviews:

No comments