– 37 –
Adjustment procedures
Results of Improper adjustment
5) Position of the thread trimmer cam
1. Loosen setscrews
6
of the thread trimmer cam and clamping
screw
7
of the lower shaft set collar.
2. Set the thread trimmer solenoid to initial position.
3. Adjust so that the clearance between the thread trimmer cam
roller
!0
and dwell section of the thread trimmer cam
!1
is 0.1
± 0.05 mm in the state that the moving knife driving arm link
8
is in contact with the moving knife driving arm roller
9
. Then
tighten setscrews
6
of the thread trimmer cam.
4. Make the lower shaft set collar
!2
come in close contact with
the thread trimmer cam
!1
, then securely tighten clamping
screw
7
of the lower shaft set collar.
6) Adjusting the knife pressure
o
Knife pressure
1. Loosen setscrews
1
of the moving knife.
2. Adjust the installing position of the moving knife
2
so that the
position where moving knife
2
and counter knife
3
start com-
ing in contact with each other starts at the position of 6 to 7 mm
from the top end of the moving knife
2
.
At this time, if moving knife
2
comes in contact with the clamp
spring, the knife pressure is increased by the clamp pressure.
So, adjust the knife pressure in the state that the clamp pres-
sure is not applied to the knife.
3. Tighten setscrews
1
of the moving knife.
(Caution) �perate the sewing machine with the knife pressure
minimized to such an extent that both needle and
bobbin threads can be trimmed.
o
Initial position
1. Loosen clamping screw
4
of the moving knife driving arm.
2. Adjust so that the distance between the top end of the counter
knife
3
and the top end of the moving knife
2
is 2 ± 0.5 mm
when moving knife
2
travels to its back end.
3. Tighten clamping screw
4
of the moving knife driving arm so
that there is no thrust play at the moving knife shaft
5
.
When there is no clearance be-
tween the thread trimmer cam
!1
and the thread trimmer cam roller
!0
:
o
Thread trimmer cam
!1
inter-
feres with the thread trimmer
cam roller
!0
resulting in break-
age or machine lock.
When the clearance between the
thread trimmer cam
!1
and the
thread trimmer cam roller
!0
is
large :
o
Defective thread trimming will
result.
When the knife pressure is high :
o
Blade sections of the counter
knife
3
and the moving knife
2
may be damaged.
o
Torque at the time of thread trim
-
ming is increased resulting in
motor-stop.
o
Defective thread trimming opera-
tion will result.
When the knife pressure is low :
o
Defective thread trimming will
result.
海外講習会用121122 LU-2810(-7)̲EM
Summary of Contents for LU-2810 Series
