17
JBP-RR-MANUAL |
©
2022 JUICED BIKES
16
JBP-RR-MANUAL |
©
2022 JUICED BIKES
wrench. The pedals must be very tight. Check and retighten
the pedals after your first two rides.
Fig. 11 - Installing Petals
ADJUSTING SEAT HEIGHT
Fig. 12 - Adjusting seat height
1.
When adjusting seat height, be sure to keep the minimum
insertion lenght inside the seat tube. This is marked in the
seatpost.
INSTALLING THE PEDALS
NOTICE
It’s critical that the pedals are tightened firmly in the crank arm to prevent the pedals
from loosening while riding, which will result in significant damage to the bike.
1.
Identify the left and right markings on the pedals. Be sure
to install the pedals on their respective side.
•
“L” is for the left pedal and is installed on the left crank arm.
•
“R” is for the right pedal and is installed on the right crank
arm (chain side).
Fig. 10 - Left and Right Identification Marks
NOTE:
Both pedals tighten toward the front of the e-bike. Right
pedal is tighened to the right. Left pedal is tightened to the left.
2.
While keeping the pedal horizontal, carefully hand-start the
threads of the pedal into the crank arm.
3.
Finish tightening the pedals using the supplied 15 mm
ASSEMBLY
OPERATION - BASIC LED
4
NOTE:
Be sure all the items you installed are properly torqued,
tightened and connected. If you have any questions, contact us.
INITIAL RIDE
NOTE:
Users can ride the e-bike like a normal bicycle with the
power turned ON or OFF. However, the pedal assist and throttle will
activate only if the power is turned ON.
We recommend that you ride your e-bike with the pedal assist
off at first, to get familiar with the braking and gear shifting.
Then, you can start testing the pedal assist levels incrementally
to gain familiarity with the optimal settings for your riding style.
SAFETY CHECK BEFORE EACH RIDE
•
The battery pack must be charged and secured.
•
Remove keys from battery pack.
•
The display must turn on and function properly.
•
The brakes must function properly.
•
The tires must be inflated to the proper psi.
•
The front and rear lights must work properly.
•
The cable connections must be tight.
•
Wheels should be secured and the spokes tight
USING THE BRAKES
The e-bike is equipped with front and rear disc brakes. Their
main function is to slow down or to stop the bicycle.
NOTE:
Apply the rear brake before using the front brake in
low-traction conditions.
•
The brake on the front wheel is controlled by the lever on
the left-hand side of the handlebar.
•
The brake on the rear wheel is controlled by the lever on
the right-hand side of the handlebar.
•
The front brake provides the majority of the e-bike’s
stopping power.
•
When slowing down on slippery surfaces, use the rear
brake first before applying the front brake.
•
A signal wire from each brake lever automatically turns off
the motor when either brake is being used. This feature
prevents undue wear on the electric motor and battery.
Your new brakes will undergo a “bedding-in” period and will
wear down after the first 40-50 full stops. The brakes will reach
100% of their grip capacity after this period. Adjust the brake
lever so that it adapts to the newly bedded-in brakes.
PEDAL ASSIST CONTROL SYSTEM
The pedal assist control system also is known as a “pedelec.”
The pedal assist uses cadence sensors that measure your
pedaling. This information transfers to the bike’s controller,
which generates the needed power. The control system can be
used to maintain a constant level of pedal assist.
USING THE PEDAL ASSIST CONTROL SYSTEM
1.
Before installing the battery pack, press the battery power
button to turn on the battery. The LED will illuminate in
