9. Front Wheel Alignment
9.1.
Put the vehicle on level ground.
9.2.
The “toe-in” of the front wheels should be 0.63 inches. To check alignment, measure
distance A and B between the centerline (CL) of the wheels. The proper toe-in
dimension A should be 0.63 inches greater than dimension B.
9.3.
To adjust the alignments, loose the lock nuts on both sides of Front Tie Rods. To make
Dimension B smaller, turn the rod to the left. Turn the rod to the right to make
Dimension B larger. After adjusted to desired length, tighten the lock nut against the
rod end. Recheck the dimensions for proper alignment.
10. Cleaning Instructions
Keep your Off highway recreational vehicle clean. With a clean rag, wipe off any dirt and
oil from around controls. Wipe off any spilled fuel and oil. Keep the engine clean of foreign
object and be sure to check that air intake fan is free of debris for proper cooling.
11. Off highway recreational vehicle Lubrication
Lubricate vehicle every 90 days of use, Apply several drops of oil in specific points.
12. Storage Instruction
In the event your Off highway recreational vehicle is not to be operated for periods in
excess of 30 days or at the end of each driving season prepare for storage as follows:
12.1.
Drain fuel tank by allowing engine to run out of fuel, or use a fuel stabilizer.
12.2.
Lubricate engine cylinder by removing the spark plug and pour one ounce of clean
lubricating oil through the spark plug hole into the cylinder. Crank the engine slowly to
spread oil and replace spark plug.
12.3.
Do not save or store gasoline over winter. Using old gasoline, which has deteriorated
from storage, will cause hard starting and affect engine performance.
Do not drain fuel while engine is hot. Be sure to move Off highway
recreational vehicle outside before draining fuel
.
FIGURE 34
Summary of Contents for JNSZ800MV
