Jøtul I 350 Installation And Operating Instructions Manual Download Page 18

18

ENGLISH

The required air vent sizes for Jøtul I 

350 

/ Jøtul I 

350 

FL  (for air

circulation) are:
Base:

Minimum of 

500 

cm

2

 

free ventilation.

Top:

Minimum of 

750 

cm

2

 free ventilation.

This is a safety measure to prevent a build up of heat in the
surround, and also to ensure sufficient heat emission into the
room.

If the house is badly ventilated, the room must be equipped
with extra fresh air circulation, for example by means of separate
air channels or a separate channel directly to the top of the
fireplace. See 

fig. 

2

.

The fresh air channel should be as straight as possible. It should
be possible to close the channel with a damper in order to keep
out cold air when the fireplace is not being used.

4.4 

Ceiling

Jøtul I 

350

 / Jøtul I 

350

 FL have been approved for:

min. 400 mm

 distance from warm air opening in the hood’s

top to a ceiling of c0mbustible material.

4.5

 Chimney

The fireplace can

 be connected to a chimney and flue pipe

approved for solid fuel fired fireplaces with flue gas
temperatures specified in 

«

2.0

 Technical data»

.

The chimney’s cross-section must be at least as big as the
flue pipe’s cross-section. See 

«

2.0 

Technical data» 

when

calculating the correct chimney cross-section.

Several fireplaces can be connected to the same chimney if
the chimney’s cross-section is sufficient.

Connection to the chimney must be carried out in accordance
with the installation instructions from the supplier of the
chimney.

Before making a hole in the chimney the fireplace should
be test-mounted in order to correctly mark the position of
the fireplace and the hole in the chimney.  See 

fig. 

1

 for

minimum dimensions.

Ensure that the flue pipe is inclined all the way up to the
chimney.

Use a flue pipe bend with a sweeping hatch that allows it to
be swept.

Be aware of the fact that connections must have a certain
flexibility in order to prevent movement in the installation
leading to cracks.

N.B. A correct and sealed connection is very important for the
proper functioning of the product.

Warning! Weight from the fireplace must not be transferred to
the chimney. The fireplace must not interfere with the ability of
the chimney to move and it must not be fastened to the chimney.

Note:

 A guide is published by the British Flue and Chimney

Manufacturers’ Association which contains general information
on chimneys and flues.

The chimney draught should never exceed 

2 . 5  

mm H

2

O

(

25

 Pa) when the fireplace is in use.

If the draught is too strong you can install and operate a flue
damper to control the draught.

In case of chimney fire

Close all hatches and vents.

Keep the firebox door closed.

Check the loft and cellar for smoke.

Call the fire service.

Before use after a fire an expert must check the fireplace in
order to ensure that it is fully functional.

4.

6

P

reparation/installation

Make sure that the fireplace insert is free of damage before
commencing with the installation.

The product is heavy! Make sure you have assistance when
erecting and installing the fireplace.

Attaching the legs (fig. 

3

 and 

4

)

Unpack the insert and take out the box with its contents.

Remove the log retainer 

(

3

A).

Remove the baffle plate (the vermiculite plate) 

(

3

B)

.

Remove the side burn plates 

(

3

C)

 by lifting them up a little

and then out. (Be aware if using tools, that vermiculite plates
may be damaged by rough handling).

Unscrew the screws at the back of the rear burn plate 

(

3

D)

and remove the burn plate. Make sure the gasket is intact
and properly positioned.

Remove the ash cover and then lift up and remove the
inner bottom plate. Close the door.

Place the wooden pallet and the cardboard packaging on
the floor and lay the fireplace carefully down on its back.

Assemble the 

4  

legs 

(

4

A)

 with the adjustable joints

(

4

C)

 with the aid of 

screws and washers, which are in the

plastic bag. Attach the joints to the product with the aid of

countersunk screws 

(

4

B)

  M

8

x

25

mm. These are already

attached to the base of the fireplace. Adjust the legs so that
the required height is achieved.

Lift the insert up.

Assembly of the ash collection system (fig. 

5

)

Open the door.

Remove the baffle plate, the side burn plates and the ash
cover 

(

5

A)

.

Lay a gasket 

(

5

B)

 (enclosed in the box) under the edge of

the ash pail mantle.

Lower the ash pail mantle 

(

5

C) 

down through the bottom

of the combustion chamber.

Lock the ash pail mantle with 4 plate screws from the inside

(

5

D)

.

Fasten the heat shield to the floor under the bottom of the
ash pail mantle with M6x10mm screws and nuts

Put the ash compartment  into position in the mantle 

(

5

E)

.

NB! The side which does not have a lip is placed against the
back wall.

Reinstall all parts that were removed.

The adjustments to the legs should only be made after the
insert has had a trial assembly. The bracket 

(

6

C)

 should be

placed under the screw heads, both to protect the surface and
to prevent the insert from slipping out of place. The final
adjustment is done with the aid of M

10

x

45

mm screws which

are attached to the joints.

Summary of Contents for I 350





























































Reviews: