background image

TM-21x1 Series Room Temperature Module Installation Instructions 

3

TM-2191 Modules

  

Installing the TM-21x1

To install the TM-21x1 Series Room Temperature 
Module:

1.

Use the Allen-head tool to loosen the security 
screw located at the top center of the housing.

2.

Insert a screwdriver blade or coin into the slot on 
the top of the housing.

3.

Press down gently, and pry the housing away from 
the base. As the two parts separate, remove the 
blade or coin and continue to pull the housing away 
from the base until the housing is free.

4.

Pull the wires through the base. Locate the green 

terminal blocks in the upper right of the base and 

position the module on the wallbox with the 

terminal numbers right-side up.

5.

Mount the base to the wallbox using the two #6-32 
mounting screws (included).

6.

Wire the controller to the module. See the 

Wiring

 

section for correct wiring.

7.

Attach the housing to the base and tighten the 
security screw with the allen-head tool.

Mounting

Location Considerations

Mount the TM-21x1 Series Room Temperature Module 
on a wall in the room to be controlled where the 
occupant can easily read and adjust the setpoint dial or 
fan speed override adjustment dial. Consider these 
additional guidelines in determining the best mounting 
location:

Avoid areas subject to excessive vibration, 
electrical noise, direct sunlight, or the effects of 
radiant heat.

Keep electrical wiring as short as possible to 
minimize temperature error.

Install modules in areas where the temperature is 
representative of the general room conditions.

Wiring

To wire a controller to the TM-21x1 Series Room 
Temperature Module, see the appropriate wiring 
diagram (Figure 6 to Figure 10).

Note:

Use 22 AWG (0.65 mm diameter) wire 

minimum. Do not exceed 164 ft (50 m) between the 
controller and the temperature module. 

Figure 5: TM-2191 Dimensions, in. (mm)

F

IG

:2

1

9

1

_

d

im

3.15 (80)

1.38 (35)

4.72

(120)

Setpoint

Adjustment

Dial

Table 1:  Nominal Values for 10k ohm Sensors

Temperature

Resistance

F

C

ohm

20

-7

48,525

30

-1

34,919

40

4

27,550

50

10

19,898

60

16

12,246

70

21

11,993

80

27

9,222

90

32

7,510

100

38

5,874

110

43

4,871

120

49

3,956

130

54

3,277

Summary of Contents for TM-2161








Reviews: