manualshive.com logo in svg

Johnson Controls PCV1617, Installation Instructions Manual, Page: 27 / 28

Share
Download
Johnson Controls PCV1617 Installation Instructions Manual Download Page 27

Table 10: PCV1617 and PCV1632 Controllers

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment.
FCC Compliant to CFR47, Part 15, Subpart B, Class A.

Canada:

UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205,

Signal Equipment
Industry Canada Compliant, ICES-003

Europe:

CE Mark – Johnson Controls declares that this product is in

compliance with the essential requirements and other relevant

provisions of the EMC Directive.

Australia and New Zealand:

RCM Mark, Australia/NZ Emissions Compliant.

Compliance

BACnet International

BACnet Testing Laboratories (BTL) Protocol Revision 7 Listed

BACnet Application Specific Controller (B-ASC)

The performance specifications are nominal and conform to acceptable industry standard. For

application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson

Controls shall not be liable for damages resulting from misapplication or misuse of its products.

Points of single contact

APAC

Europe

NA/SA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 32 CHANGJIJANG RD NEW DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

27

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

Summary of Contents for PCV1617





























Reviews:

No comments