manualshive.com logo in svg

Johnson Controls PCV1617, Installation Instructions Manual, Page: 20 / 28

Share
Download
Johnson Controls PCV1617 Installation Instructions Manual Download Page 20

Setting the EOL switch

Each PC controller has an EOL switch, which when set to ON (up), sets the PC controller as a

terminating device on the bus. See Figure 10 for the EOL switch location on the PC. The default EOL

switch position is OFF (down). The amber EOL LED illuminates to show that the EOL is active.

Figure  10: EOL switch positions

To set the EOL switch on a PC controller:

1.  Determine the physical location of the PC controller on the SA or FC Bus.
2.  Determine if the PC controller must be set as a terminating device on the bus.

Note: 

The EOL termination rules for SA Buses and FC Buses are different.

3.  If the PC is a terminating device on the FC Bus, set the EOL switch to ON. If the field controller

is not a terminating device on the bus, set the EOL switch to OFF.

Note: 

When the EOL switch is set to ON, the LED light on the face of the controller is

illuminated.

Commissioning

Use the following procedure to commission the PCV1617 or PCV1632 controller:

1.  Download the control application to the PCV controller using the Controller Configuration Tool

(CCT). Refer to the 

Controller Tool Help (LIT-12011147)

.

2.  Commission the VAV Box. Refer to the 

Controller Tool Help (LIT-12011147)

.

3.  Perform airflow balancing on the VAV box. Refer to the 

VAV Balancing Tool and Network Sensors

Technical Bulletin (LIT-12011087)

.

4.  Perform commissioning checkout procedures. Refer to the 

Controller Tool Help (LIT-12011147)

.

The CCT connects to the PCV through a laptop computer using different connection options: the

Bluetooth

®

 Commissioning Converter, or the wired BACnet Ethernet to MS/TP Router can be used

when using the BACnet MS/TP protocol.

Repair information

If the PCV1617 or PCV1632 controller fails to operate within its specifications, replace the unit. For a

replacement unit, contact the nearest Johnson Controls representative.

PCV1617 and PCV1632 VAV Box Controllers Installation instructions

20

Summary of Contents for PCV1617





























Reviews:

No comments