Johnson Controls NIE29 Series Installation Instructions Manual Download Page 32 | Manualshive

Page: 32 / 32

background image

Table 19: NIE29

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management Equipment,

FCC Compliant to CFR47, Part 15, Subpart B, Class A

Compliance

Canada:

UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205, Signal Equipment,

Industry Canada Compliant, ICES-003

Europe

CE Mark - Johnson Controls declares that this product is in compliance with the

essential requirements and other relevant provisions of the EMC Directive.

Australia and New Zealand

RCM Mark, Australia/NZ Emissions Compliant

BACnet International:

BACnet Testing Laboratories

™

(BTL) 135-2010 Listed BACnet

Building Controller (B-BC)

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions
beyond these specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for
damages resulting from misapplication or misuse of its products.

North American Emissions Compliance

United States

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area may cause harmful interference, in which case the users will be required to correct the interference
at their own expense.

Canada

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

APAC Single Point of Contact:

NA/SA Single Point of Contact:

European Single Point of Contact:

JOHNSON CONTROLS

C/O CONTROLS PRODUCT
MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

Building Technologies & Solutions

507 E. Michigan Street, Milwaukee, WI 53202

Metasys

®

and Johnson Controls

®

are registered trademarks of Johnson Controls.

All other marks herein are the marks of their respective owners.

©

2017 Johnson Controls

www.johnsoncontrols.com

Published in U.S.A.

32

NIE29 Installation Instructions

«
...
30
31
32

Summary of Contents for NIE29 Series

































Reviews:

No comments

Related manuals for NIE29 Series

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 2

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 98

Brand: NAiS Pages: 173

Brand: Panasonic Pages: 2

Brand: KAR-TECH Pages: 28

Brand: 2M Technology Pages: 17

Brand: 2iB Pages: 5

Go!Control Panel

Brand: 2gig Technologies Pages: 78

Brand: Jafar Pages: 10

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

VARIVENT D Series

Brand: GEA Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands