manualshive.com logo in svg

Johnson Controls NIE29 Series, Installation Instructions Manual, Page: 31 / 32

Share
Download
Johnson Controls NIE29 Series Installation Instructions Manual Download Page 31

Technical Specifications

Table 19: NIE29

Dedicated nominal 24 VAC, Class 2 power supply (North America), SELV power supply
(Europe), at 50/60 Hz (20 VAC minimum to 30 VAC maximum)

Power Requirement

25 VA maximum for NCE25 only

The 25 VA rating does

not

include any power supplied to devices connected at the NIE binary

outputs (BOs). Binary output devices connected to and powered by an NIE can require an
additional 125 VA (maximum).

Power Consumption

0 to 50°C (32 to 122°F); 10 to 90% RH, 30°C (86°F) maximum dew point

Ambient Operating Conditions

-40 to 70°C (-40 to 158°F); 5 to 95% RH, 30°C (86°F) maximum dew point

Ambient Storage Conditions

Supports data protection on power failure. Rechargeable NiMH battery: 3.6 VDC 500 mAh,
with a typical life of 5 to 7 years at 21°C (70°F); Product Code Number: MS-BAT1020-0

Data Protection Battery

Supervisory Controller:

192 MHz Renesas

®

SH4 7760 RISC processor

Field Controller:

20 MHz Renesas H8S2398 processor

Processors

Supervisory Controller:

128 MB flash nonvolatile memory for operating system, configuration

data, and operations data storage and backup and 128 MB synchronous dynamic random
access memory (SDRAM) for operations data dynamic memory

Field Controller:

1 MB flash and 1 MB RAM

Memory

Microsoft

®

Windows

®

CE embedded

Operating System

One Ethernet port, 10/100 Mbps, 8-pin RJ-45 connector

One optically isolated RS-485 SA Bus port; with a pluggable and keyed 4-position terminal
block (all NIE29xx-x models)

One optically isolated RS-485 FC Bus port; with a pluggable and keyed 4-position terminal
block (only on NIE29 models that support an N2 Bus or MS/TP Bus trunk)

One L

ON

W

ORKS

port; FTT10 78 Kbps; pluggable, keyed 3-position terminal block (only on

NIE29 models that support a L

ON

W

ORKS

network trunk)

One RS-232-C serial port with standard 9-pin sub-D connector that supports standard baud
rates

One USB serial port with standard USB connector

Network and Serial Interfaces

Analog Input Points: 16-bit resolution

Analog Output Points: 16-bit resolution and +200 mV accuracy on 0-10 VDC applications

Analog Input/Analog Output

Resolution and Accuracy

155 x 270 x 64 mm (6.1 x 10.6 x 2.5 in.)

Minimum mounting space required: 250 x 370 x 110 mm (9.8 x 14.6 x 4.3 in.)

Dimensions (Height x Width x
Depth)

Plastic housing

Plastic material: ABS and polycarbonate

Protection: IP20 (IEC60529)

Housing

On flat surface with screws on three mounting clips or a single 35 mm DIN rail

Mounting

1.2 kg (2.7 lb)

Shipping Weight

31

NIE29 Installation Instructions

Summary of Contents for NIE29 Series

































Reviews:

No comments