Johnson Controls Metasys NAE55 Installation Manual Download Page 20

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond

these specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from

misapplication or misuse of its products.

Single point of contact

APAC

EU

UK

NA/SA

JOHNSON CONTROLS
C/O CONTROLS
PRODUCT MANAGEMENT
NO. 32 CHANGJIANG RD
NEW DISTRICT
WUXI JIANGSU PROVINCE
214028
CHINA

JOHNSON
CONTROLS
VOLTAWEG 20
6101 XK ECHT
THE NETHERLANDS

JOHNSON
CONTROLS
TYCO PARK
GRIMSHAW LANE
MANCHESTER
M40 2WL
UNITED KINGDOM

JOHNSON
CONTROLS
5757 N GREEN BAY
AVE.
GLENDALE, WI
53209
USA

North American emissions compliance

United States

This equipment has been tested and found to comply with

the limits for a Class A digital device pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications. Operation

of this equipment in a residential area may cause harmful

interference, in which case the users will be required to

correct the interference at their own expense.

Warning (Part 15.21)

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

Canada

This Class (A) digital apparatus meets all the requirements

of the Canadian Interference-Causing Equipment

Regulations.
Cet appareil numérique de la Classe (A) respecte toutes

les exigences du Règlement sur le matériel brouilleur du

Canada.

Industry Canada Statement(s)

This device complies with Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two

conditions:

1.  This device may not cause interference, and
2.  This device must accept any interference, including

interference that may cause undesired operation of

the device.

Le présent appareil est conforme aux CNR d'Industrie

Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions

suivantes :

1.  L'appareil ne doit pas produire de brouillage, et
2.  L'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le

fonctionnement.

Product warranty

This product is covered by a limited warranty, details

of which can be found at 

www.johnsoncontrols.com/

buildingswarranty

.

Software terms

Use of the software that is in (or constitutes)

this product, or access to the cloud, or hosted

services applicable to this product, if any, is

subject to applicable end-user license, open-source

software information, and other terms set forth at

www.johnsoncontrols.com/techterms

.

 Your use of this

product constitutes an agreement to such terms.

Patents

Patents: 

https://jcipat.com

Contact information

Contact your local branch office:

www.johnsoncontrols.com/locations

Contact Johnson Controls: 

www.johnsoncontrols.com/

contact-us

© 2022 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and

are subject to change without notice.

www.johnsoncontrols.com

Summary of Contents for Metasys NAE55





















Reviews: