manualshive.com logo in svg

Johnson Controls Metasys NAE55, Installation Manual, Page: 16 / 20

Share
Download
Johnson Controls Metasys NAE55 Installation Manual Download Page 16

Table 20: Maximum number of devices per LonWorks network segment

Device Type

Maximum Allowed

Free Topology

One free topology terminator required (NU-EOL203-0)

Notes:

• Each LPT10/11 channel segment (between repeaters) requires its own power supply. Other factors, such as power

consumption of individual LPT10/11 devices, may limit a segment to fewer devices.

• The MS-NAE552x-x models that support LonWorks Network trunks do not have an internal network terminator.

Table 21: NAE55 with integrations trunk options

Trunk Type

Supported Trunk Application

Modbus

• 2 RS485 or

• 2 RS232 or

• 2 TCP or

• 1 RS232 + 1 RS485 or

• 1 RS232 + 1 TCP or

• 1 RS485 + 1 TCP

M-Bus

• 2 RS485 or

• 2 RS232 or

• 2 TCP or

• 1 RS232 + 1 RS485 or

• 1 RS232 + 1 TCP or

• 1 RS485 + 1 TCP

Modbus and M-Bus

• 1 RS485 1 RS485 M-Bus or

• 1 RS232 1 RS232 M-Bus or

• 1 TCP 1 TCP M-Bus or

• 1 RS232 1 RS485 M-Bus or

• 1 RS485 1 RS232 M-Bus or

• 1 TCP 1 RS232 M-Bus or

• 1 TCP 1 RS485 M-Bus or

• 1 RS232 1 TCP M-Bus or

• 1 RS485 1 TCP M-Bus

KNX

• 1 KNX (routing mode) or

• 3 KNX (tunneling mode)

Repair information

If you replace a network engine for any reason or add a

new network engine to a site, you must update the site

registration to ensure that the new network engine is

recognized and able to communicate on the Metasys

system site. For details refer to the 

Replacing an NAE

section in the 

NAE Commissioning Guide (LIT-1201519)

.

Except for replacing the data protection battery, the

network engine cannot be repaired in the field. If the

network engine fails to operate, it must be replaced.
Batteries removed from this device must be recycled

or disposed of in accordance with local, national, and

regional regulations. Only trained technicians or qualified

building maintenance personnel should service Johnson

Controls products.

Ordering information

The following table lists the product code numbers for all

available NAE55 network engines based on model. If you

receive an NAE55 engine from the factory that is imaged

with Release 10.1, you can field-upgrade the engine to

Release 11.0 if the upgrade is supported.

Note: 

Some network engines are also available in

a Buy American version (add a 

G

 after the product

code number). For repair parts, specify 

703

 in place

of the last digit of the product code number.

NAE55 Installation Guide

16

Summary of Contents for Metasys NAE55





















Reviews:

No comments