Johnson Controls JRC Series Installation Operation & Maintenance Download Page 4

WAT E R - S O U R C E   H E AT   P U M P S

JRC-Series

R e v. :   D e c e m b e r   8 ,   2 0 2 1

I n s t a l l a t i o n ,   O p e r a t i o n ,   M a i n t e n a n c e

4

General Information

Safety

Warnings, cautions, and notices appear throughout this 

manual. Read these items carefully before attempting any 

installation, service, or troubleshooting of the equipment. 

DANGER:

 Indicates an immediate hazardous situation, 

which if not avoided will result in death or serious injury. 

DANGER labels on unit access panels must be observed.

WARNING:

 Indicates a potentially hazardous situation, 

which if not avoided could result in death or serious injury.

CAUTION:

 Indicates a potentially hazardous situation or 

an unsafe practice, which if not avoided could result in 

minor or moderate injury or product or property damage.

NOTICE:

 Notification of installation, operation, or 

maintenance information, which is important, but which is 

not hazard-related.

WARNING!

 To avoid the release of refrigerant into the 

atmosphere, the refrigerant circuit of this unit must be 

serviced only by technicians who meet local, state, and 

federal proficiency requirements.

 

WARNING!

 

 

WARNING!

 

 

WARNING!

 

WARNING! 

The installation of water-source heat pumps and 

all associated components, parts, and accessories which 

make up the installation shall be in accordance with the 

regulations of ALL authorities having jurisdiction and MUST 

conform to all applicable codes. It is the responsibility of 

the installing contractor to determine and comply with ALL 

applicable codes and regulations.

WARNING! 

This appliance is not intended for use by persons 

(including children) with reduced physical, sensory, or mental 

capabilities, or lack of experience and knowledge, unless 

they have been given supervision or instruction concerning 

use of the appliance by a person responsible for their safety.

WARNING! 

All refrigerant discharged from this unit must 

be recovered WITHOUT EXCEPTION. Technicians must 

follow industry accepted guidelines and all local, state, and 

federal statutes for the recovery and disposal of refrigerants. 

If a compressor is removed from this unit, refrigerant circuit 

oil will remain in the compressor. To avoid leakage of 

compressor oil, refrigerant lines of the compressor must be 

sealed after it is removed.

CAUTION! 

To avoid equipment damage, DO NOT use 

these units as a source of heating or cooling during the 

construction process. The mechanical components and filters 

can quickly become clogged with construction dirt and debris, 

which may cause system damage and void product warranty.

 

WARNING!

 

 

CAUTION!

 

WARNING!

 This product can expose you to chemicals 

including formaldehyde, which is known to the state of 

California to cause cancer. For more information, go to 

www.P65Warnings.ca.gov.

 

WARNING!

 

Summary of Contents for JRC Series













































Reviews: