manualshive.com logo in svg

Johnson Controls FX-PCV Series, Installation Instructions Manual, Page: 22 / 22

Share
Download
Johnson Controls FX-PCV Series Installation Instructions Manual Download Page 22

Table 9: FX-PCV16 Controllers

Dimensions
(Height x Width x

Depth)

182 mm x 182 mm x 64 mm (7-3/16 x 7-3/16 x 2-1/2 in.)

Note: 

Center of output hub to center of anti-rotation slot is 160mm

(6-5/16 in.).

Weight

0.86 kg (1.9 lb)

United States:

 UL Listed, File E107041, CCN PAZX, UL 916, Energy

Management Equipment; FCC Compliant to CFR47, Part 15, Subpart B,

Class A

Canada:

 UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205,

Signal Equipment; UL Listed, File S4977, UUKLC ULC-ORD-C100-13,

Smoke Control System Equipment (MS-VMA1610-0U, MS-VMA1610-1U,

MS-VMA1620-0U, and MS-VMA1620-1U models only); Industry Canada

Compliant, ICES-003

Europe:

 CE Mark – Johnson Controls declares that this product is

in compliance with the essential requirements and other relevant

provisions of the EMC Directive.

Australia and New Zealand:

 RCM Mark, Australia/NZ Emissions

Compliant.

Compliance

BACnet International:

 BACnet Testing Laboratories (BTL) Protocol

Revision 7 Listed BACnet Application Specific Controller (B-ASC)

1

For more information, refer to the 

FX-PC Series Controllers MS/TP Communications Bus Technical Bulletin (LIT-12011670).

The performance specifications are nominal and conform to acceptable industry standard. For

application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson

Controls shall not be liable for damages resulting from misapplication or misuse of its products.

Points of single contact

APAC

Europe

NA/SA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 32 CHANGJIJANG RD NEW DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

© 2019 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document

revision and are subject to change without notice.

www.johnsoncontrols.com

Summary of Contents for FX-PCV Series























Reviews:

No comments