background image

FX-BTCVT Bluetooth® Commissioning Converter Installation Instructions 

7

Troubleshooting

Status Indication Light-Emitting Diodes (LEDs)

The Converter has 4 LEDs (Figure 1) to indicate power 
and communication status. Table 4 describes the LED 
functions.

For other troubleshooting, refer to the Controller Tool 

Help (LIT-12011147)

.

LED Test Sequence at Startup

During startup, the Converter automatically initiates an 
LED test to verify the operational status of the LEDs. 
Immediately after connecting supply power, the 
following LED lighting sequence occurs:

1.

All LEDs light up.

2.

The Power LED remains lit while all other LEDs go 
to Normal operation as indicated in Table 4.

Repair Information

If the Bluetooth Commissioning Converter fails to 
operate within its specifications, replace the unit. For a 
replacement Bluetooth Commissioning Converter, 
contact the nearest Johnson Controls® representative.

Do not remove the blue protective boot or open the 
Converter housing. The Converter has no 
user-serviceable parts inside.

The Bluetooth Commissioning Converter requires no 
periodic field maintenance.

Technical Specifications      

Table 4:  Converter LED Designations and Descriptions

Color

LED Name

Normal

Descriptions/Other Conditions

Green

Power

On Steady

On Steady = Power is Supplied by Primary Voltage
Off = No Power

Red

Fault

Off

Off Steady = No Faults
On Steady = Device Fault

Green

SA/FC Bus

Flicker

Flicker = MS/TP Bus Activity
Off Steady = No MS/TP Bus Activity

Blue

Link

On When 
Connected

On Steady = Bluetooth communication link established
Off Steady = Bluetooth communication link not established

Bluetooth Commissioning Converter (Part 1 of 2)

Product Code

FX-BTCVT-1

Power Requirement

Nominal 15 VDC, provided through the SA/FC Bus Port

Power Consumption

1.35 W Maximum

Ambient Operating 
Temperature

0 to 50°C (32 to 122°F)

Ambient Operating Conditions

 5 to 95% RH, Noncondensing, 30°C (86°F) Maximum Dewpoint

Ambient Storage Temperature

-40 to 85°C (-40 to 185°F) 

Ambient Storage Conditions

 5 to 95% RH, Noncondensing 

Transmission Power

2.5 mW Maximum

Transmission Speed

Wireless Communication

115.2k bits per second (bps)

Serial Communication (SA/FC Bus)

9.6k, 19.2k, 38.4k, or 76.8k bps

Transmission Range (Typical)

Wireless Communication

10 m (33 ft) line-of-sight

Wireless Security

Security Mode 3 - Link Level Enforced Security

Network and Serial Interfaces

Bluetooth Wireless Technology
One RS-485 Bus

Summary of Contents for FX-BTCVT









Reviews: