Johnson Controls FMS-2000C User Manual Download Page 18

Page: 18 / 62

FMS-2000C

LIT-12013504

Network setup

In the network menu, you can set up the network communications between the FMS-2000C Critical Environment Controller and the

facility. Each FMS-2000C controller is set up for BACnet® MS/TP by default. The Metasys N2 network can be enabled on the controller.

BACnet MS/TP network setup

On the BACnet MS/TP network, you can adjust the device ID offset, MaxMaster, baud rate and MAC address.

Setting up the device ID offset

The FMS-2000C controller includes a feature that groups devices from the same manufacturer within a range of device instance

numbers by specifying the device ID offset parameter. The FMS-2000C sets the device instance number automatically as the sum of the

device ID offset and the current MAC address. The device ID offset can range from zero to 4,194,000 in increments of 1,000. To specify

the device ID offset, select a number between zero and 4,194. The FMS-2000C automatically multiplies the number entered by 1,000

to configure the resulting device ID offset. For example, if the MAC address is 25, and the device ID offset is 85, the resulting device

instance number calculated by the FMS-2000C controller is 85,025.

To set up the device ID offset, complete the following steps:

1. On the home screen, tap the

Settings

icon to enter the

Settings

menu.

2. To view network settings, tap

Network

3. To view the

Device ID Offset

, tap

BACnet Protocol

4. To adjust the

Device ID Offset

, tap the

Arrow

icon.

5. Enter a number between zero and 4,194 and multiply this value by 1000.

To confirm the new settings, tap the

Checkmark

icon.

Setting up the MaxMaster

This parameter specifies the highest allowable address for a master node on the same network. The default value for this parameter

is 127. Set this parameter to a lower value than the default to reduce the number of addresses polled by each master node on the

network. This effectively improves the overall networking efficiency.

1. On the home screen, tap the

Settings

icon to enter the

Settings

menu.

2. To view network settings, tap

Network

3. To view the

MaxMaster

, tap

BACnet Protocol

4. To adjust the

MaxMaster

, move the slider towards the

Plus

icon to increase or the

Minus

icon to decrease the parameter. You can

also tap the

Plus

Minus

icon to make adjustments.

Optional:

Tap the

Revert

icon to revert back to the previous setting.

To confirm the new settings, tap the

Checkmark

icon.

Choosing the baud rate

Complete the following steps to set the baud rate when using a BACnet MS/TP configuration:

1. On the home screen, tap the

Settings

icon to enter the

Settings

menu.

2. To view network settings, tap

Network

3. To set the

Baud Rate

, expand

Baud Rate

and select the appropriate rate.

4. To save the new settings, collapse

Baud Rate

Setting the MAC address for BACnet MS/TP

On the BACnet MS/TP protocol, you can set up a MAC address within a valid range of 4 to 127 to support master mode.

1. On the home screen, tap the

Settings

icon to enter the

Settings

menu.

2. To view network settings, tap

Network

3. On the Network screen, tap

MAC Address

4. To adjust the

MAC Address

, move the slider towards the

Plus

icon to increase or the

Minus

icon to decrease the parameter. You

can also tap the

Plus

Minus

icon to make ad

justm

ents.

Optional:

Tap the

Revert

icon to revert back to the previous setting.

To confirm the new settings, tap the

Checkmark

icon.

Summary of Contents for FMS-2000C































































Search results

Summary of Contents for FMS-2000C

Reviews:

Related manuals for FMS-2000C

Brands by name

Popular brands

Johnson Controls FMS-2000C, User Manual

Search results

Summary of Contents for FMS-2000C

Reviews:

Related manuals for FMS-2000C

Brands by name

Popular brands