Johnson Controls F4-SNC Installation Manual Download Page 2

Page: 2 / 26

Figure 2: F4-SNC16121-0x

Table 1: Physical features of the SNC25151-0x and

SNC16121-0x

Callout

Physical features

Binary Outputs (BO) removable terminal

blocks. See

Connecting input and output

terminals

for more information.

Configurable Outputs (CO) removable

terminal blocks. See

Connecting input and

output terminals

for more information.

Analog Output (AO) removable terminal

blocks. See

Connecting input and output

terminals

for more information.

Rotary switch dials: controller number. Ships

from the factory at setting 000. See

Rotary

switch dials

for more information.

Supply power removable terminal block:

gray terminals; 24 VAC, Class 2.

Two Universal Serial Bus (USB) 2.0 host type

A ports.
USB-1 (top port): Any Johnson Controls

approved USB device can be connected to

the top port.
USB-2 (bottom port): Any non-wireless,

Johnson Controls approved USB device can

be connected to the bottom port.

Note:

There is one micro-USB port that

is reserved for future use.

Sensor/Actuator (SA) Bus port: RJ12 6-Pin

Modular Jack.

Table 1: Physical features of the SNC25151-0x and

SNC16121-0x

Callout

Physical features

Field Controller (FC) Bus port: RJ12 6-pin

Modular Jack.

Field Controller (FC) Bus removable terminal

block: blue terminal. See

FC Bus terminal

block

for more information.

End-of-Line (EOL) switch.

Sensor Actuator (SA) Bus removable

terminal block: brown terminal. See

SA Bus

terminal block

for more information.

Binary Input (BI) removable terminal blocks.

See

Connecting input and output terminals

for more information.

SNC input terminal blocks cover

Universal Inputs (UI) removable terminal

blocks. See

Connecting input and output

terminals

for more information.

Two active Ethernet ports, 1000/100/10

Mbps; 8-pin RJ45 connector, labeled

ETH-1

(top) and

ETH-2

(bottom).

Multi-color LED status indicators. See

LED

status indicators

for more information.

Reset button. See

Reset button

for more

information

Recovery button. See

Recovery button

for

more information.

F4-SNC Installation Guide

Summary of Contents for F4-SNC



























Search results

Summary of Contents for F4-SNC

Reviews:

Related manuals for F4-SNC

Brands by name

Popular brands

Johnson Controls F4-SNC, Installation Manual

Search results

Summary of Contents for F4-SNC

Reviews:

Related manuals for F4-SNC

Brands by name

Popular brands