manualshive.com logo in svg

Johnny Vac JVC70RIDER, Operator'S Manual

Share
Download
Johnny Vac JVC70RIDER Operator'S Manual Download Page 33

33

JVC70RIDER

OPERATOR MANUAL

www.johnnyvac.com

Maintenance

Squeegee Blade Adjustment

Adjust the squeegee at a level surface to make sure the edge of it can totally contact 

the ground to be scrubbed. 

FOR SAFETY: Stop the machine on a level surface, turn it off, and remove the key 

before leaving or servicing.
1. Check whether squeegee blade totally contacts and maintains an inclined angle of 
45°with the ground. 
2. Adjust the regulating nut as indicated by arrow 2 

in the following diagram if squeegee blade does not 

contact the ground or there is a small gap between 

them. Clockwise rotate the regulating nut to lift the 

squeegee blade; anti-clockwise rotate the regulating nut 

to lower the squeegee blade. Adjust the squeegee blade 

to an optimal status according to actual demands. 
3. Adjust the regulating nut as indicated by arrow 1 in the following diagram if the 

middle of squeegee blade contacts the ground well but 

there is a small gap between left side of blade and the 

ground. Clockwise rotate the regulating nut to lift the 

left squeegee blade; anti-clockwise rotate the regulating 

nut  to  lower  the  left  squeegee  blade. Adjust  the 

squeegee blade to an optimal status according to actual 
demands.
4. Adjust the regulating nut as indicated by arrow 3 in the following diagram if the 

middle of squeegee blade contacts the ground well but there is a small gap between 

the right side of blade and the ground. Clockwise rotate the regulating nut to lift 

the right squeegee blade; anti-clockwise rotate the regulating nut to lower the right 

squeegee blade. Adjust the squeegee blade to an optimal status according to actual 

demands.
5. Anti-clockwise rotate the regulating nut as indicated by arrow 2 in the following 

diagram if both sides of squeegee blade contact the ground well but there is a small 

gap between middle of blade and the ground. Be sure the blade contacts the ground 

well or it forms an inclined angle of 45°with the ground. Adjust the squeegee blade 

following step 2 or 3 if either side of blade needs adjusting.

Summary of Contents for JVC70RIDER









































Reviews:

No comments

Brands by name

Popular brands

Load more brands