manualshive.com logo in svg

Johnny Vac JVC70RIDER, Operator'S Manual

Share
Download
Johnny Vac JVC70RIDER Operator'S Manual Download Page 19

19

JVC70RIDER

OPERATOR MANUAL

www.johnnyvac.com

Operation

Recovery Tank Full Indicator

The recovery tank full indicator will shut off the power supply of vacuum motor 

without disabling scrubbing functions when the tank is full. Please drain it timely to 

guarantee scrubber's proper operation. 

Battery Voltage Indicator

Battery voltage indicator displays battery capacity.
All the (10) indicator lamps will be on when the battery gets fully charged and then 

and then go out in sequence form right to left with electricity consumption. When 

battery electricity is exhaust, the left-most lamp (red) blinks. 
In this case, the machine will stop scrubbing to warn the operator of current battery 

voltage. When the indicator blinks, the machine will stop for charging. 

NOTE:

 Frequent charging is not allowed, it is better to charge the batteries when 

necessary; over charging will shorten battery service life. Do not charge the machine 

until the left-most indicator lamp blinks; the left-most indicator lamp won't stop 

blinking until the batteries are fully charged. 

Full indicator shield 

Recovery tank full indicator

Summary of Contents for JVC70RIDER









































Reviews:

No comments

Brands by name

Popular brands

Load more brands