background image

Service to the Power Direct Vent System should only be
performed by a qualified service technician.

The manufacturer and seller of this water heater will not
assume any liability for any property damage, personal
injury or death resulting from improper sizing, installation or
failure to comply with these instructions.

The warranty on this water heater is in effect only when the
water heater is installed and operated in accordance with
these instructions. A data plate identifying your water heater
can be found next to the gas control/thermostat. When
referring to your water heater, always have the information
listed on the data plate readily available.

Protect your warranty:

Regularly service your water

heater as directed in the "Maintenance" section of this man-
ual.
Retain your original receipt as proof of purchase.

Do not discard this manual. You or future users of this
water heater will need it for reference.

II) SAFETY

This water heater is design-certified by CSA International as
a Category I, direct vented water heater which takes its
combustion air from the outside of the structure and
exhausts all products of combustion to the outside of the
structure.

In addition to the installation instructions found in this man-
ual, the water heater must be installed in accordance with
all local and provincial or state codes or, in the absence of
such, with the latest editions of the following specifications.

For Installations in Canada:

“Natural Gas and Propane Installation Code” CAN/CSA-
B149.1

and

“Canadian Electrical Code (CAN/CSA C22.1), Part I”

available from:

Canadian Standards Association,
5060 Spectrum Way,
Mississauga, Ontario, Canada
L4W 5N6

For Installations in the United States:

“National Fuel Gas Code” ANSI Z223.1 (NFPA 54)

and

“National Electrical Code” (NFPA 70)”

available from:

American National Standards Institute,
25 West 43rd Street,
New York, NY 10036

Massachusetts code

requires this water heater to be

installed in accordance with Massachusetts Plumbing and
Fuel Gas Code 248 CMR Section 2.00 and 5.00.

Check your phone listings for the local authorities having
jurisdiction over your installation.

Safety Warning (Flammable Vapours)

There is a risk of property damage, personal injury or death
from the by-products of combustion (e.g., flue gases), in
using fuel-burning appliances such as water heaters. Areas
that may not be suitable for water heater installation include
those where flammable liquids, gasoline, solvents, adhe-
sives etc. are stored, or where engine-driven equipment or
vehicles are stored, operated or repaired. These, and simi-
lar products, should not be stored or used near the water
heater or air intake. Due to the nature of air movement,
flammable vapours can be carried some distance from the
point of storage. The gas-fired water heater igniter or burn-
er flame can ignite these vapours causing a flashback, fire
or explosion, which may result in severe property damage,
serious personal injury or death. If flammable liquids or
vapours have spilled or leaked in the area of the water
heater, leave the area immediately and call the fire depart-
ment from a neighbor’s home. Do not attempt to clean the
spill until all ignition sources have been extinguished.

Safety Warning (Scalding)

Hot water produced by this appliance can cause severe
burns due to scalding. The hazard is increased for young
children, the aged or the disabled when water temperatures
exceed 52°C (125°F). Use tempering valves, also known as
mixing valves, in the hot water system to reduce the risk of
scalding at point-of-use such as lavatories, sinks and
bathing facilities. Such precautions must be followed when
this heater is operated in combination with dishwashing or
space heating applications.

– 5 –

WARNING

Flammable Vapours

FLAMMABLES

FIRE AND EXPLOSION HAZARD

Can result in serious injury or death

Do not store or use gasoline or other flammable vapours and liquids

in the vicinity of this or any other appliance. Storage of or use of gasoline

or other flammable vapours or liquids in the vicinity of this or any other

appliance can result in serious injury or death.

DANGER

Summary of Contents for 4040SN-PDV



































Reviews: