manualshive.com logo in svg

John Bean EEWH553A Series, Operation Instructions Manual

Share
Download
John Bean EEWH553A Series Operation Instructions Manual Download Page 27

 - Page 27 - 

Operation Instructions

3.0 PRE-INSTALLATION INSTRUCTIONS

Check that the machine onto which this device is to 
be mounted is installed in work area large enough to 
accommodate the addition of this device.

The installation of this device increases the changers 
footprint requirement only slightly.

Insure that enough space is left around the machine to 
prevent compression or entrapping hazards.

Make sure that from the operating position, the opera-
tor can see all the machine and the surrounding area.

The operator shall forbid the presence of non autho-
rized persons and of objects which may create possible 
hazards.

THE AIR INSTALLATION MUST BE MADE ONLY BY 
LICENSED PERSONNEL IF LOCAL RESTRICTIONS 
APPLY.

Ensure that the input line pressure is within the mini-
mum/maximum limits (110-170psi) required by the 
machine.

If air pressure is lower than the minimum required of 
110 psi, the force of the device may be insuffi cient for 
certain types of tires.

After checking all the above proceed as follows:

DISCONNECT ELECTRIC AND AIR SUPPLY FROM 
THE CHANGER BEFORE INSTALLATION OF THIS  
DEVICE.

3.1  INSTALLATION INSTRUCTIONS
A.

 Place the drilled template/spacer plate “A” as shown 

in Figure 1. The square angle must be in contact with 
the side wall of the Cabinet 

and 

with the reinforcement 

welds.

IMPORTANT!  THE DRILLED PLATE (“A” FIGURE 
1) MUST BE LEFT AS A SPACER BETWEEN THE 
DEVICE AND THE BEAD BREAKER BEAM.

B.

 Drill 4 (1/2”) holes all the way through the bead 

breaker beam using plate “A” as a template.

Figure 1

 - Place template/spacer, mark location and 

drill holes.

A

Figure 2

 - With template/spacer in position, place 

the device onto the breaker arm beam. Secure with 
supplied hardware.

Bolts, washers and 
nuts in four places

1

2

3

4

4
5

C.

 Lift the device with an appropriate lifting device, 

(engine hoist, fork lift) and a sling belt of suffi cient 
capacity  - 1100 lbs.  Attach the device ( #1 in Figure 
2) to the bead breaker beam (#2) with the bolts (#3), 
washers (#4) and nuts (#5) supplied.

Summary of Contents for EEWH553A Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands