background image

2

1. SPECIFICATIONS

Model

CT5611

Voltage

230V~

Frequency

50Hz

Power

60W

Working temperature

200

o

C-450

o

C

Protection class

I

Waterproof

IP X0

1. IMPORTANT SAFETY INFORMATION

General safety instructions
● To operate this device safely, the user must have read and understood these
instructions for use before using the device for the first time.
● Observe all safety instructions! Failure to do so may cause harm to you and
others.
● Retain all instructions for use, and safety instructions for future reference.
● If you sell or pass the device on, you must also hand over these operating
instructions.
● The device must only be used when it functions properly. If the product or part
of the product is defective, it must be taken out of operation and disposed of
correctly.
● Never use the device in a room where there is a danger of explosion or in the
vicinity of flammable liquids or gases.
● Always ensure that a device which has been switched off cannot be restarted
unintentionally.Do not use devices with an on/off switch that does not function
correctly.
● Keep children away from the device! Keep the device out of the way of children
and other unauthorised persons.
● Do not overload the device. Do not use the device for purposes for which it is
not intended.
● Exercise caution and only work when in good condition: If you are tired, ill, if
you have ingested alcohol,medication or illegal drugs, do not use the device, as

Summary of Contents for CT5611

















Reviews: