background image

 

This  document  is  only  for  internal  use  of  JINNENG  CLEAN  ENERGY  TECHNOLOGY  LTD,  and  shall  not  be  published  or 
copied without permission of the company.

 

If the container is on the ground, the 
module can be unloading directly. 

 

If the container is not full

the people need to 

cut  the  bandage  when  unloading(If  the 
container is full

the bandage is none).   

If  the  container  is  on  the  flatbed 
trailer,  the  module  need  a  landing 
platform when unloading. 

 

 

1. Before  the  forklift  operate,  add  some 
buffer  articles  at  the  forklift  arm  to  avoid 
damaging the module.   
2. Box  transportation  needs  to  keep 
horizontal  or  tilted  to  the  direction  of 
forklift. 
3. The  vertical  surface  of  the  forklift  arm 
should  be  smooth  and  there  are  no 
something that sticks out. 
4. Start from the short side of the packing 
box, reduce modules that are broken. 
5. When  second transportation, a special 
person should be command to carry, and 
it  is  prohibited  to  damage  the  packing 
box. 
6. During  operation,  the  forklift  truck 
should  not  hit  the  pallet  including  the 
pallet wooden pier.

 

The forklift can loading  3T or more, 
raising the module smoothly pull out 
and keep slow  speed  when  holding 
the module. 

 

1. Box 

transportation 

needs 

to 

keep 

horizontal or tilted to the direction of forklift. 
2. The  vertical  surface  of  the  forklift  arm 
should  be  smooth  and  there  are  no 
something that sticks out. 

2. Vertical - container loading 

S/N 

Operating Procedure   

Photo 

Control Point 

If the container is on the ground, the 
module can be unloading directly.

 

 

If the container is not full

the people need to 

cut  the  bandage  when  unloading(If  the 
conta    iner is full

the bandage is none).

 

If  the  container  is  on  the  flatbed 
trailer,  the  module  need  a  landing 
platform when unloading. 

 

1. Before  the  forklift  operate,  add  some 
buffer  articles  at  the  forklift  arm  to  avoid 
damaging the module.   
2. Box  transportation  needs  to  keep 
horizontal  or  tilted  to  the  direction  of 
forklift. 
3. The  vertical  surface  of  the  forklift  arm 
should  be  smooth  and  there  are  no 
something that sticks out. 

Summary of Contents for JNBM120



























Reviews: