-3-
DO NOT RETURN your Jiffy Power Ice Drill TO THE
RETAILER THAT SOLD IT TO YOU. THEY MAY NOT BE
AUTHORIZED TO PROVIDE REPAIRS OR WARRANTY
REPLACEMENT. If you have any questions concerning
service, contact Feldmann Engineering as indicated in the
Service & Repair Information section of this manual.
ASSEMBLY AND DISASSEMBLY OF DRILL AND POWERHEAD
Jiffy E-Z Connect™ Collar
Connect drill assembly to powerhead by sliding E-Z Connect™
Collar down and pulling clevis pin out. Then slide drill assembly onto
output shaft. Reinsert clevis pin through drill assembly and output
shaft, then slide E-Z Connect™ Collar up over clevis pin and twist
collar slightly to lock pin in place.
Note: Do not remove clevis pin from collar
tether.
OIL & FUEL RECOMMENDATIONS
IMPORTANT NOTE: A
40-1
MIXTURE OF
FRESH WINTER BLEND
GAS AND HIGH QUALITY 2-CYCLE OIL IS NEEDED TO RUN THIS
ENGINE. NEVER RUN ON STRAIGHT GAS, OR ANY MIXTURE
OTHER THAT
40-1
AS SERIOUS ENGINE DAMAGE WILL
RESULT AND VOID ALL WARRANTY OF YOUR ENGINE.
TO OPERATE YOUR DRILL, YOU WILL NEED THE FOLLOWING:
USE OF
JIFFY®
SPECIALLY FORMULATED 2-CYCLE
OIL IS RECOMMENDED. (DO NOT USE MULTI-
VISCOSITY OILS).
CLEAN, FRESH,
WINTER BLEND
, UNLEADED
REGULAR FUEL ONLY.
USE OF FUEL WITH THE
LOWEST ETHANOL PERCENTAGE IS
RECOMMENDED.
FUEL MUST BE FRESH AND CLEAN. NEVER USE FUEL
LEFT OVER FROM LAST SEASON OR STORED FOR
LONG PERIODS. DO NOT USE FUEL CONTAINING
METHANOL (WOOD ALCOHOL).
DO NOT USE
SUMMER BLEND FUEL.
NOTE:
THE USE OF ALTERNATIVE FUELS SUCH
AS E85, E20 OR E15 ARE NOT
RECOMMENDED FOR USE IN JIFFY ICE
DRILLS. ALTERNATIVE FUELS WITH HIGH
ALCOHOL CONTENT CAN CAUSE HARD
STARTING, POOR PERFORMANCE, AND
INTERNAL ENGINE DAMAGE. NEVER MIX
OR STORE GASOLINE/OIL MIXTURE
INDOORS OR IN ENCLOSED, POORLY
VENTILATED ENCLOSURES, WHERE FUEL
FUMES MAY REACH AN OPEN FLAME,
SPARK OR PILOT LIGHT AS ON A
FURNACE, WATER HEATER, CLOTHES
DRYER, ETC.
DAMAGE AND/OR PERFORMANCE
PROBLEMS THAT WILL OCCUR FROM USE
OF FUELS, OTHER THAN THOSE LISTED
IN THE MANUAL WILL NOT BE
CONSIDERED WARRANTY.
TO MIX OIL AND GASOLINE
1. Mix
a
FRESH WINTER BLEND
gasoline and
JIFFY®
2-Cycle Engine
Oil, Part #4024, in an approved, clean, safety-type container. Inferior
quality gasoline or oil may damage the engine, sealing rings, fuel lines
or fuel tank.
2. Add recommended oil to gasoline per FUEL MIX CHART. DO NOT
MIX DIRECTLY IN ENGINE FUEL TANK. Pour oil into container first
then add gasoline.
3.
Securely screw cap on container and shake vigorously. Once mixed, oil
and gasoline should not separate.
FUELING
1. Gasoline vapor pressure may build up inside gas tank of a two cycle
engine depending on weather conditions, venting system of the tank,
and the fuel used. To reduce the risk of injury from escaping gas fumes
and vapor, remove the gas cap on your drill slowly to release pressure
build-up.
2. Fill fuel tank with fuel mixture specified in the preceding “Oil and Fuel
Recommendations”.
+
NEVER FILL FUEL TANK INDOORS, WHILE ENGINE IS RUNNING,
OR WHILE ENGINE IS HOT.
+
NEVER FILL FUEL TANK COMPLETELY. FILL TANK TO ½ INCH
BELOW BOTTOM OF FILLER NECK TO PROVIDE SPACE FOR
FUEL EXPANSION. WIPE ANY FUEL SPILLAGE FROM ENGINE
AND EQUIPMENT BEFORE STARTING ENGINE.
CHECK THE FOLLOWING BEFORE STARTING YOUR DRILL
1.
Be sure spark plug wire is ATTACHED to spark plug.
2.
Be sure ignition switch is in the ON Position.
3.
Inspect the machine for proper condition and operation, paying special
attention to the throttle control assembly, on/off switch, and drilling
assembly.
+
TO REDUCE THE RISK OF INJURY FROM THE TURNING DRILL
ASSEMBLY OR FROM REACTIVE FORCES, THE THROTTLE
ASSEMBLY AND RELATED MECHANISM MUST MOVE FREELY
AND RETURN IMMEDIATELY TO THE IDLE POSITION WHEN
RELEASED.
+
NEVER OPERATE YOUR DRILL IF IT HAS BEEN DAMAGED,
IMPROPERLY ADJUSTED OR NOT COMPLETELY AND
SECURELY ASSEMBLED.
+
NEVER RUN ENGINE INDOORS OR IN ENCLOSED, POORLY
VENTILATED AREAS. ENGINE EXHAUST CONTAINS CARBON
MONOXIDE, AN ODORLESS AND DEADLY GAS.
+
TO REDUCE THE RISK OF INJURY FROM REACTIVE FORCES,
THE OPERATOR MUST HAVE A FIRM GRIP ON THE MACHINE
AND A GOOD FOOTHOLD BEFORE STARTING THE DRILL AND
OPENING THE THROTTLE.
+
KEEP HANDS, FEET, HAIR AND LOOSE CLOTHING AWAY
FROM ANY MOVING PARTS ON ENGINE AND EQUIPMENT.
+
WARNING – TEMPERATURE OF MUFFLER AND NEARBY
AREAS MAY EXCEED 150° F (65° C) AVOID THESE AREAS TO
AVOID BURNS OR OTHER INJURY.
FUEL MIX CHART
MIXTURE 40:1
U.S. METRIC
Gas Oil To Be Added Petrol Oil To Be Added
1 Gal. 3.2 oz. 4 Liters 100 ml