If you find any, you must stop using the product, until the damage is removed. Contact the shop you bought the product from
or the importer.
2.Make sure that the plastic parts of the toy are not cracked or broken.
3.From time to time use lubricating oil, in order to oil the moving parts such as wheels and moving connections. You must
apply a very thin layer of the oil and be careful while applying it.
4.Store the jeep in upright position only, do not turn it upside down and do not tilt it. Park the battery operated jeep indoors or
cover it with sailcloth, in order to protect it in humid weather.
5.When you are not going to use the product, you must store it at a dry, cool and well ventilated place. Do not store the
product close to sources of heat – open fire, heating devices or cookers and also at humid places.
6.FOR ADULTS ONLY:
recharge the battery after each use. Recharge the battery at least once a month, when you are not
using the battery operated jeep.
7.When the battery operated jeep is not being used, all electric sources must be switched off. All switches must be in zero
position or in “stop” position. Disconnect the bushings of the battery’s cables.
8.If you are not going to use the product for a long time, you must charge the battery completely
,
before you put it for
storage. You must charge the battery every three months in order to prolong its life.
9.Before you put the jeep for storage you must switch the power button OFF, remove the cables from all bushings and the
rechargeable battery of the jeep. Store it at a suitable place (dry, cool and well ventilated place). Do not allow children to
play close to the battery.
10.IMPORTANT!
DO NOT MAKE ANY CHANGES OF THE BODY OF THE JEEP AND ITS MAIN PARTS AND ALSO THE
ELECTRIC INSTALLATION! This may lead to damaging of the jeep, improper operation and a risk of injury to the child.
These parts must be maintained by an expert – authorized repair shop or importer.
11.Do not charge non-rechargeable batteries, do not mix old and new or different types of batteries. Observe the correct
polarity while placing the batteries.
12.Do not change the structure of this product and its electric system. Any changes must be performed under the guidance
of a technician only. In case of a problem contact the shop you bought the product from or the importer.
TROUBLESHOOTING GUIDE
Problem
Possible Reason
Solution
The battery operated
jeep does not move
Circuit breaker tripped
Circuit breaker may “trip“ and stop the vehicle of it is overloaded or the
driving conditions are too severe. The breaker will automatically reset
after approximately 10 seconds, and the vehicle will operate normally.
To avoid repeated automatic shut downs, do not overload the vehicle
by exceeding the weight limit of 40 kg, or by towing anything behind
the vehicle. Do not drive uphill or run into fixed objects, which can
cause the wheels to stop spinning while power is still being supplied to
the motors.
Loose wire or connectors
Check all wires and connectors. Make sure that the motor connectors
are plugged in tightly to the battery, and that there are no loose wires
around the motor.
Dead Battery
Change the battery with new and
for this purpose contact the ship,
from which you bought the product.
Undercharged battery
A new battery should have been charged for at least 12 hours before
using the vehicle for the first time. After that, it must be recharged for
at least 8 – 10 hours after each use. Never charge longer than 24
hours. Check all connectors, make sure the charger is plugged into
the wall. Make sure the power flow to the outlet is on.
Charger is not working
You must have a volt meter in order to tell whether the charger is
working or not. If you think there is problem with your charger,
contact
the shop you bought the product from.
Electricity switch damages
When exposed to water or moisture, electricity can become corroded,
or can jam due to loose dirt, sand or gravel.
The battery operated
jeep is running but then
suddenly stops
Loose wire or connectors
Check all wires and connectors. Make sure that the motor harness
connector is plugged into the battery tightly, and that there are no
loose wires around the motor.
21
Summary of Contents for HL228
