manualshive.com logo in svg

JFD B44771, Operation And Maintenance Manual, Page: 92 / 136

Share
Download
JFD B44771 Operation And Maintenance Manual Download Page 92

80

OM131

Chapter 4

P1939-OM-131 R11

4. 

Clean off the old silicone and wipe the contact areas with silicone primer (Divex Part No.
SM021).

5. 

Fit a new O-ring (Fig 4.11, Item 3) to the upper penetrator (Fig 4.11, Item 1) and apply a bead
of silicone sealant (Divex Part No. SM006) around the sealing face of the penetrator.

6. 

Re-install the penetrator into the scrubber housing and refit the locknut (Fig 4.11, Item 2)
using the tools described in Step 2 above, and with a moistened finger carefully wipe the
excess silicone sealant smooth before it sets.

Fig 4.11 Corrective Maintenance Under Penetrator (Typical)

Counterlung Hose Penetrators:

Inhale / Exhale Hose Penetrators:

Item

Description

Part No

1

Duct

D2487G

2

Locknut

D275

3

O-ring

RN031-7

Item

Description

Part No

1

Duct

D2437

2

Locknut

D270

3

O-ring

RN031-7

Summary of Contents for B44771









































































































































Reviews:

No comments