JFD B44771 Operation And Maintenance Manual Download Page 48 | Manualshive

Page: 48 / 136

JFD B44771 Operation And Maintenance Manual Download Page 48

36

OM131

Chapter 3

P1939-OM-131 R11

6.

Charge the SLS System to the required charging pressure (see Table 3.2 for details). Slowly
pressurise the gas cylinders. Ensure, using torch, that an excessive temperature rise does
not occur within the cylinders during this operation. If the cylinders become too warm to touch,
stop charging and leave the cylinders to cool before continuing.

The use of a Divex portable booster skid (Divex Part No. DM1480) is recommended to assist in
charging if the required cylinder charging pressure is greater than that available from storage.

N

OTES

(1) When charging the SLS System using enriched oxygen mixes (mixes containing greater than

21% oxygen), the gas booster should not be required. These gases should be decanted directly
into the SLS System. The required charging pressures are given on the Table 3.2.

(2) After carrying out shallow training dives with the SLS System, care must be taken to ensure that

the O

2

rich mixture used is fully vented from the SLS System before recharging with the correct

gas mix for the proposed working depth. After completion of training dives, the cylinders should
be vented, then charged then vented again and then recharged to ensure the gas mix for the
working depth has not been compromised.

7.

Vent the charging whip and disconnect.

8.

Replace the blanking cap on the charging point.

«
...
46
47
48
49
50
...
»

Summary of Contents for B44771









































































































































Reviews:

No comments