manualshive.com logo in svg

JFD B44771, Operation And Maintenance Manual, Page: 104 / 136

Share
Download
JFD B44771 Operation And Maintenance Manual Download Page 104

92

OM131

Chapter 5

P1939-OM-131 R11

5.1 B

ACKPACK

 

HOUSING

 

ASSEMBLY

 

DRAWINGS

 

AND

 

PARTS

 

LISTS

Following are the detailed assembly drawings and their associated parts lists. Together these
provide details of all parts used within the SLS System Backpack. All parts can be obtained from
Divex Ltd.

Drawing No.

MTO Number

Description

P1939229S1 (Fig 5.2)

-

SLS System (MK IV) Backpack Assy

P1939110S1 (Fig 5.3)

P1939-MT-110

SLS System (MK IV) Housing Assy

P1939131S1 (Fig 5.4)

-

SLS System (MK IV) Srubber Housing Assy

P193982606S1 (Fig 5.5)

-

SLS System (MK IV) Lid Screw Assy

P1939-DG-142 (Fig 5.6)

P1939-MT-142

SLS System (MK IV) Inhale/Exhale Duct Assy

P1939-DG-159 (Fig 5.7)

P1939-MT-159

SLS System (MK IV) Counterlung Duct Assy

P1939129S1 (Fig 5.8)

-

SLS System (MK IV) Supply Penetrator Assy

P1939040S1 (Fig 5.9)

-

SLS System (MK IV) Gas System Schematic

P193933S1 (Fig 5.10)

-

SLS System Two Stage Regulator Assy

P1939-DG-031 (Fig 5.11)

-

SLS System Single Stage Regulator Assy

P1939-DG-025 (Fig 5.12)

-

SLS System (MK IV) Demand Regulator Assy

P1939272S1 (Fig 5.13)

-

SLS System (MK IV) Protection Cover Assembly

P193982626 (Fig 5.14)

82626-SL

SLS System (MK IV) Bottle Retainer Assy

P1939-DG-059 (Fig 5.15)

P1939-MT-059

SLS System (MK IV) Rotowink General Assy

P1939156S1 (Fig 5.16)

-

SLS System (MK IV) Hot Water Schematic

P193983281S1 (Fig 5.17)

-

SLS System Set Hot Water Hose Assembly

P193983282 (Fig 5.18)

-

SLS System (MK IV) Shroud Hot Water Hose Assy

P193982840 (Fig 5.19)

82840-MT

SLS System (MK IV) Hot Water Shroud Assy

P1939-DG-035 (Fig 5.20)

-

SLS System Refillable Canister Assy

P1939137S1 (Fig 5.21)

-

SLS System (MK IV) Harness Assy

P1939-DG-115 (Fig 5.22)

-

SLS System (MK IV) Actuation Cable Assy

P1939-DG-056 (Fig 5.23)

-

SLS System (MK IV) Counterlung Assy

P1939-DG-204 (Fig 5.24)

-

SLS System (MK IV) Tool & Test Kit

Summary of Contents for B44771









































































































































Reviews:

No comments