manualshive.com logo in svg

JFD B44771, Operation And Maintenance Manual, Page: 9 / 136

Share
Download
JFD B44771 Operation And Maintenance Manual Download Page 9

OM131

vii

P1939-OM-131 R11

Warnings

W

ARNINGS

1. 

Failure to maintain the SLS System Mk IV Backpack in accordance with this Manual (using
original SLS System spare parts) or use by a person or persons unfamiliar with its operation,
could result in a serious hazard or fatal injury to personnel.

2. 

This SLS System Mk IV Backpack contains a high-pressure helium / oxygen mixture for
breathing purposes. Only special purpose, oxygen compatible, lubricant (e.g. Christo-lube
fluorinated grease - Divex Part No. SM034) should be used on specified components that
come into contact with high pressure, oxygen rich mixtures.

3. 

Naked lights or smoking in the vicinity of the gas cylinders may cause an explosion.

4. 

The system must be depressurised before disconnecting any part of the gas system.

5. 

Due to the very high levels of energy stored within compressed gas, it is potentially very
dangerous. Care must therefore be taken when charging the gas cylinders and safety
goggles must be worn. Ear defenders should also be worn.

6. 

Care must be taken to ensure that the replacement intervals specified in this Manual are
adhered to for all components.

7. 

Care must be exercised in the storage of the SLS System Mk IV Backpack to ensure that it is

maintained in a clean state, ready for use. If it is to be stored at temperatures below 0

o

C, it is

essential that the equipment is dried thoroughly before storage.

8. 

Correct planning of any operation using the SLS System is essential.

Summary of Contents for B44771









































































































































Reviews:

No comments